ROPS Kit

• The ROPS is an integral safety device. Do not remove any of the ROPS components from the machine.

• Ensure that the seat belt is attached and that you can release it quickly in an emergency.

• Always wear your seat belt when the roll bar is installed.

• Check carefully for overhead objects before you drive under them, and do not contact them.

• Keep the roll bar in safe operating condition by thoroughly inspecting it periodically for damage and keeping all the mounting fasteners tight.

• Replace damaged ROPS components. Do not repair or alter them.

• Wheels dropping over edges, over steep banks, or into water can cause a rollover, which may result in serious injury or death.

• Do not wear the seat belt when the roll bar is not installed.

• In the event of a rollover, take the machine to an Authorized Service Dealer to inspect the ROPS.

• Use only Toro approved accessories and attachments for the ROPS.

Note: Determine the left and right sides of the machine from the normal operating position.

Note: You may discard all removed parts unless otherwise noted.

1. Park the machine on a level surface.

2. Disengage the blade-control switch.

3. Move the motion-control levers outward to the NEUTRAL-LOCK position to engage the parking brake.

4. Shut off the engine and remove the key.

5. Raise the seat, refer to your machine Operator’s Manual.

6. Raise the rear of the machine on jack stands; refer to your machine Operator’s Manual.

   Warning

   Supporting the machine on the lower muffler shield (Figure 1) may damage the shield and cause the machine to fall, injuring you or bystanders.

   Do not use the lower muffler shield to support the machine.

   

   Figure 1

   1. Lower muffler shield

7. Remove the rear tires as shown in Figure 2

   Note: Retain all wheel components for later installation.

   

   Figure 2

8. Remove the pod brackets from the machine (Figure 3).

   Note: Retain the shoulder screws removed from the sides of the pods for later installation.

   

   Figure 3

   1. Hydraulic mount plate
   2. Screw
   3. Pod support bracket
   4. Pod

   Note: Retain the fuel tank spring beneath that secures the fuel tank to the left pod bracket for later installation.

   

   Figure 4

   1. Fuel tank spring

Parts needed for this procedure:

1. Install the ROPS mounts to the machine frame behind the hydraulic mount plate as shown in (Figure 5).

2. Torque the bolts to 58 to 77 N∙m (43 to 57 ft-lb).

3. Secure the tabs on the pods to the ROPS mount with narrow push rivets (Figure 5).

4. Install the teeth of the rear guard panel to the notches in the center frame and secure it with cable ties as shown in Figure 6.

5. Install the belt guard panels to the frame with push rivets as shown in Figure 6.

   

   Figure 5

   Right side shown

   1. Locknut (1/2 inch)
   2. Right ROPS mount
   3. Narrow push rivet
   4. Large washer
   5. Bolt (1/2 x 1-1/4 inches)
   

   Figure 6

   1. Cable tie
   2. Wide push rivet
   3. Rear guard panel
   4. Narrow push rivet
   5. Belt guard panels

Parts needed for this procedure:

1. Install the seat belt brackets to the seat platform with 2 partial-thread bolts (3/8 x 2 inches), 2 small washers, and 2 locknuts (3/8 inch) as shown in Figure 7.

   

   Figure 7

   1. Partial-thread bolts (3/8 x 2 inches)
   2. Small washer
   3. Seat belt bracket
   4. MyRide platform
   5. Locknut (3/8 inch)

2. Install the bumper to the left pod bracket (Figure 8).

   

   Figure 8

   1. Bumper

3. Install the left pod bracket to the machine frame using 2 thread-forming screws (5/16 x 3/4 inch) and the parts removed in Preparing the Machine as shown in Figure 9.

   

   Figure 9

   1. Left pod bracket
   2. Thread-forming screw (5/16 x 3/4 inch)
   3. Fuel-tank spring
   4. Shoulder bolt

4. Install new right pod bracket to the machine using a thread-forming screw (5/16 x 3/4 inch) and the shoulder bolt removed in Preparing the Machine.

   

   Figure 10

   1. Thread-forming screw (5/16 x 3/4 inch)
   2. Right pod bracket
   3. Shoulder bolt

5. Install the seat belt buckle and tongue to the inside of the seat belt brackets with 2 carriage screws (7/16 x 1 inch) and 2 locknuts (7/16 inch) as shown in Figure 11.

   

   Figure 11

   1. Carriage screws (7/16 x 1 inch)
   2. Seat belt bracket
   3. Seat belt tongue assembly (bracket bent toward the seat)
   4. Locknut (7/16 x 1 inch)

Parts needed for this procedure:

1. Install the seat belt buckle and tongue to the inside of the seat belt brackets with 2 carriage screws (7/16 x 1 inch) and 2 locknuts (7/16 inch) as shown in Figure 12.

   

   Figure 12

   1. Carriage screw (7/16 x 1 inch)
   2. Seat belt bracket
   3. Buckle
   4. Locknuts (7/16 inch)
   5. Tongue assembly

2. Install the seat belt brackets to the outside of the ROPS mounts (Figure 13).

   Note: Install the seat belt buckle assembly with the bent bracket toward the seat.

   

   Figure 13

   Right side shown

   1. Bolt (3/8 x 1 inch)
   2. Seat belt bracket
   3. Locknut (3/8 inch)

3. Install the right pod bracket to the machine frame using 2 thread-forming screws (5/16 x 3/4 inch) and the parts removed in Preparing the Machine as shown in Figure 3.

4. Install the bumper to the left pod bracket (Figure 8).

5. Install the left pod bracket to the machine frame using 2 thread-forming screws (5/16 x 3/4 inch) as shown in Figure 13.

   

   Figure 14

   1. Left pod bracket
   2. Thread-forming screw (5/16 x 3/4 inch)
   3. Fuel-tank spring
   4. Shoulder bolt

Parts needed for this procedure:

1. Install the rear tires as shown in Figure 2.

2. Lower the machine; refer to your machine Operator’s Manual.

3. Lower the seat.

4. With the ROPS tube angle toward the rear of the machine, install the ROPS tube to the ROPS mounts with 2 bolts (3/8 x 2-1/2 inches) and 2 locknuts (3/8 inch) as shown in Figure 15.

5. For machines with a bagger installed only: Install the included additional suitcase weights to the machine using 2 bolts (3/8 x 3-3/4 inches) as necessary according to the table below (Figure 16).

   Type of Deck	Total Weights Required
   42-inch stamped deck	11
   42-inch fabricated deck	10
   50-inch fabricated deck	8
   54-inch fabricated deck	6
   60-inch fabricated deck	6

   Note: The weight brackets will hold up to 8 suitcase weights between the front edge of the bracket and the machine; any additional weights must be mounted to the front of the weight brackets.

   

   Figure 15

   1. ROPS tube
   2. Locknut (3/8 inch)
   3. Bolt (3/8 x 2-1/2 inches)
   

   Figure 16

   1. Washer
   2. Locknut
   3. Suitcase weight
   4. Bolt (3/8 x 3-3/4 inches)