Maintenance Service Interval | Maintenance Procedure |
---|---|
Before each use or daily |
|
This utility vehicle is intended to be primarily used off-highway to transport people and material loads. Using this product for purposes other than its intended use could prove dangerous to you and bystanders.
Read this information carefully to learn how to operate and maintain your product properly and to avoid injury and product damage. You are responsible for operating the product properly and safely.
Visit www.Toro.com for product safety and operation training materials, accessory information, help finding a dealer, or to register your product.
Whenever you need service, genuine Toro parts, or additional information, contact an Authorized Service Distributor or Toro Customer Service and have the model and serial numbers of your product ready. Figure 1 identifies the location of the model and serial numbers on the product. Write the numbers in the space provided.
Important: With your mobile device, you can scan the QR code on the serial number decal (if equipped) to access warranty, parts, and other product information.
This manual uses 2 words to highlight information. Important calls attention to special mechanical information and Note emphasizes general information worthy of special attention.
The safety-alert symbol (Figure 2) appears both in this manual and on the machine to identify important safety messages that you must follow to avoid accidents. This symbol will appear with the word Danger, Warning, or Caution.
Danger indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
Warning indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
Caution indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
This product complies with all relevant European directives; for details, please see the separate product specific Declaration of Conformity (DOC) sheet.
CALIFORNIA
Proposition 65 Warning
The power cord on this product contains lead, a chemical known to the State of California to cause birth defects or other reproductive harm. Wash hands after handling.
Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and reproductive harm. Wash hands after handling.
This machine has been designed in accordance with the requirements of SAE J2258 (Nov 2016).
This product is capable of causing personal injury. Always follow all safety instructions to avoid serious personal injury.
Read and understand the contents of this Operator’s Manual before you start the machine. Ensure that everyone using this product knows how to use it and understands the warnings.
Use your full attention while operating the machine. Do not engage in any activity that causes distractions; otherwise, injury or property damage may occur.
Do not put your hands or feet near moving components of the machine.
Do not operate the machine without all guards and other safety protective devices in place and working on the machine.
Keep bystanders and children out of the operating area. Never allow children to operate the machine.
Stop and shut off the machine and remove the key before servicing.
Improperly using or maintaining this machine can result in injury.
To reduce the potential for injury, comply with these safety instructions
and always pay attention to the safety-alert symbol , which means Caution, Warning,
or Danger—personal safety instruction. Failure to comply with
these instructions may result in personal injury or death.
![]() |
Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. |
Note: Determine the left and right sides of the machine from the normal operating position.
Parts needed for this procedure:
Steering wheel | 1 |
Steering wheel cover | 1 |
Washer (1/2 inch) | 1 |
Dust cover | 1 |
If the cover is installed, remove it from the hub of the steering wheel (Figure 3).
Remove the locknut (1/2 inch) from the steering shaft (Figure 3).
Slide the steering wheel, dust cover, and washer (1/2 inch) onto the steering shaft (Figure 3).
Note: With the front wheels straight, orient the steering wheel so that the smaller spoke on the steering wheel is vertical.
Secure the steering wheel to the shaft with the locknut (1/2 inch) and tighten it to 18 to 30 N∙m (13 to 22 ft-lb).
Install the cover on the steering wheel (Figure 3).
Check the water level in the batteries before you operate the machine; refer to Checking the Water Level of the Batteries.
Ensure that the batteries are charged; refer to Charging the Batteries.
Check the brake-fluid level before you operate the machine; refer to Checking the Brake-Fluid Level.
Check the air pressure in the tires; refer to Checking the Tire Pressure.
To ensure optimum performance of the brake system, burnish (break-in) the brakes before use.
Bring the machine up to full speed, apply the brakes to rapidly stop the machine without locking up the tires.
Repeat this procedure 10 times, waiting 1 minute between stops, to avoid overheating the brakes.
Important: This procedure is most effective if the machine is loaded with 227 kg (500 lb).
Parts needed for this procedure:
Operator's Manual | 1 |
Registration card | 1 |
Predelivery Inspection Form | 1 |
Certificate of Quality | 1 |
Key | 2 |
Read the Operator's Manual.
Fill out the registration card.
Complete the Predelivery Inspection Form.
Review the Certificate of Quality.
Become familiar with all the controls before you start the engine and operate the machine.
Use the accelerator pedal (Figure 6) to vary ground speed of the machine. Pressing down the accelerator pedal starts the machine. Pressing the pedal farther increases ground speed. Releasing the pedal slows the machine, and the machine shuts off.
The maximum forward speed in performance mode is 26 km/h (16 mph) as shown in Figure 9.
The maximum forward speed in economy mode is 19 km/h (12 mph) as shown in Figure 9.
Use the brake pedal to stop or slow the machine (Figure 6).
Operating a machine with worn or incorrectly adjusted brakes can may result in personal injury.
If the brake pedal travels to within 25 mm (1 inch) of the machine floor board, adjust or repair the brakes.
The parking-brake lever is located on the control panel (Figure 6).
Whenever you shut off the machine, engage the parking brake to prevent the machine from accidentally moving. If the machine is parked on a steep grade, ensure that you engage the parking brake.
To engage the parking brake, pull the parking-brake lever toward you (Figure 7).
To disengage the parking brake, push down the button on top of the parking-brake lever, pull the parking-brake lever toward you to release pressure, and then push the parking-brake lever forward (Figure 8).
The direction selector is located to the left of the parking-brake lever. The direction selector has 3 positions: FORWARD, REVERSE, and NEUTRAL (Figure 6).
Note: The machine can be in any of the 3 positions, but only moves in the FORWARD and REVERSE positions.
Important: Always stop the machine before changing direction.
The horn button is located on the control panel (Figure 6). Press the horn button to sound the horn.
Use the light switch (Figure 6) to illuminate the headlights. Push the light switch up to turn on the headlights. Push the light switch down to turn off the lights.
The battery-discharge indicator is located to the left of the steering column (Figure 6). The battery-discharge indicator indicates the remaining charge in the batteries. When the batteries are fully charged, 10 indicator bars extend from the 0 to the 1 position. As you use the charge, the indicator bars disappear, starting at the right side of the meter. For detailed information on the battery meter, refer to Understanding and Using the Battery System.
The hour meter is located to the right of the light switch (Figure 6). Use the hour meter to find out the total number of operating hours. The hour meter starts to function whenever you turn the key switch to the ON position or if the machine is running.
Note: When the machine is running, the hour meter blinks continuously, recording usage.
The USB power point is located to the left of the parking-brake lever (Figure 6). Use the power point to power mobile devices.
Important: When you are not using the USB power point, insert the rubber plug to prevent damage to the power point.
Use the key switch (Figure 6), to run and shut off the machine.
The key switch has 2 positions: ON and OFF. Rotate the key clockwise to the ON position to operate the machine. When you stop the machine, rotate the key counterclockwise to the OFF position to shut off the machine. Remove the key whenever you leave the machine.
The supervisor speed-limit switch, located under the seat assembly, has 2 positions: PERFORMANCE and ECONOMY. Rotate the switch clockwise to the ECONOMY position to limit the maximum machine speed to 19 km/h (12 mph). Rotate the switch counterclockwise to the PERFORMANCE position to restore the maximum speed of the machine to 26 km/h (16 mph) as shown in Figure 9.
The status-indicator light is located to the right of the parking-brake lever on the control panel (Figure 6).
When the machine is turned on, the green status-indicator light illuminates either solid or blinking.
If the light is solid, this indicates that the machine is ready for normal operation. If the light is blinking, there is an issue that needs to be resolved before continuing with normal operation of the machine.
If the status-indicator light blinks 2 times, this indicates that the parking brake is engaged while in the FORWARD or REVERSE position on the direction selector. Disengage the parking brake to shut off the status-indicator light.
Refer to if the status-indicator light blinks more than 2 times.
The passenger handholds are located on the outside of each seat (Figure 10).
Note: Specifications and design are subject to change without notice.
Base weight | Dry 633 kg (1,395 lb) |
Rated capacity (on level ground) | 544 kg (1,200 lb) total, including 91 kg (200 lb) operator and 91 kg (200 lb) passenger, load, accessories, and attachments |
Gross vehicle weight (GVW)—on level ground | 1177 kg (2,595 lb) total, including all of the weights listed above |
Maximum cargo capacity (on level ground) | 363 kg (800 lb) total, including rear-mounted accessories |
Maximum rear cargo bed accessory mount capacity | 45 kg (100 lb) total |
Tow capacity | Tongue weight: 91 kg (200 lb) |
Gross trailer weight (GTW): 680 kg (1,500 lb) | |
Overall width | 119 cm (47 inches) |
Overall length | 302 cm (119 inches) |
Overall height | 127.5 cm (50-3/16 inches) |
Ground clearance | 21.6 cm (8-1/2 inches) at the front with no load or operator |
14 cm (5-1/2 inches) at the rear with no load or operator | |
Wheel base | 220 cm (86-5/8 inches) |
Wheel tread (center line to center line) | Front: 119 cm (47 inches) |
Rear: 119 cm (47 inches) | |
Cargo bed length | Inside: 102 cm (40 inches) |
Outside: 114.3 cm (45 inches) | |
Cargo bed width | Inside: 98 cm (38-1/2 inches) |
Outside of the molded fenders: 107.3 cm (42-5/16 inches) | |
Cargo bed height | 28 cm (11 inches) inside |
*Specifications listed are with Trojan T-125 batteries.
**Installing non-standard batteries may reduce the cargo-bed capacity.
A selection of Toro approved attachments and accessories is available for use with the machine to enhance and expand its capabilities. Contact your Authorized Service Dealer or authorized Toro distributor or go to www.Toro.com for a list of all approved attachments and accessories.
To ensure optimum performance and continued safety certification of the machine, use only genuine Toro replacement parts and accessories. Replacement parts and accessories made by other manufacturers could be dangerous, and such use could void the product warranty.
Note: The procedures in this section show a machine with a plastic cargo bed and bucket seat; for additional procedures for other attachments, refer to the Operation section (if applicable) in the Installation Instructions. Visit www.Toro.com for your instructions or scan the QR code (if applicable) on your attachment.
Note: Determine the left and right sides of the machine from the normal operating position.
Never allow children or people who are not trained or physically capable to safely operate or service the machine. Local regulations may restrict the age of the operator. The owner is responsible for training all operators and mechanics.
Become familiar with the safe operation of the equipment, operator controls, and safety signs.
Shut off the machine, remove the key, and wait for all movement to stop before you leave the operator’s position. Allow the machine to cool before adjusting, servicing, cleaning, or storing it.
Know how to stop and shut off the machine quickly.
Ensure that there are not more occupants (you and your passenger(s)) than the number of handholds equipped on the machine.
Check that all safety devices and decals are in place. Repair or replace all safety devices and replace all illegible or missing decals. Do not operate the machine unless they are present and functioning properly.
Maintenance Service Interval | Maintenance Procedure |
---|---|
Before each use or daily |
|
Before starting the machine each day, perform the Each Use/Daily procedures listed in .
Maintenance Service Interval | Maintenance Procedure |
---|---|
Before each use or daily |
|
Front and rear tires air pressure specification: 165 to 207 kPa (24 to 30 psi)
Important: Do not exceed the maximum air pressure indicated on the sidewall of the tire.
Note: The air pressure needed in the tires is determined by the payload that you intend to carry.
Check the air pressure in the tires.
Use lower air pressure in the tires for lighter payloads, for less soil compaction, for a smoother ride, and to minimize tire marks on the ground.
Use higher air pressure in the tires for carrying heavier payloads at higher speeds.
If necessary, adjust the air pressure in the tires by adding or removing air in the tires.
The machine contains 8 deep-cycle, lead-acid batteries that supply power to the motor and accessories. A deep-cycle battery is not the same as an automobile battery. An automobile battery is designed to provide a surge of power to start the machine and moderate power to run the lights and accessories when the motor if off or idling. The alternator then continuously charges as the automobile runs. As such, an automobile battery seldom drops below 90% of the maximum charge level.
A deep-cycle battery is designed to be a primary power source to provide a sustained output. Deep-cycle batteries are typically discharged as low as 20 to 30% of the maximum charge level. A discharge this low is considered a deep discharge.
Important: Repeated deep-discharge cycles reduces the battery life.
Lead-acid batteries produce electricity through a chemical reaction between lead plates and sulfuric acid. Charging a battery reverses the chemical reaction, allowing the battery to once again produce electricity.
A battery is a perishable item that has a limited lifetime (Figure 12). When a battery is new, it requires a break-in period to establish efficient electrical production. This break in period usually requires 100 to 150 discharge/charge cycles.
After the break-in period, the battery maintains a high capacity for many cycles. The number of cycles that a battery performs depends on the following:
Battery maintenance—improper maintenance severely reduces the life of the batteries.
Depth of discharge between charge cycles—the deeper the batteries are discharged on a regular basis between charges, the shorter the service life the batteries will have.
Charge frequency—fully charge the batteries whenever possible.
Important: Fully discharging the batteries damages them and reduces their life.
Low water levels—if the lead plates become exposed, it may permanently damage the batteries. Perform the following to maintain the electrolyte level:
After fully charging the batteries, fill the batteries with distilled or deionized water; refer to Checking the Water Level of the Batteries and Adding Distilled or Deionized Water to the Batteries.
Important: Fully charge the batteries before adding the water to the batteries. While charging, the electrolyte increases in volume, and filling a low battery before fully charging the batteries can cause the electrolyte to overflow and leak out of the vent.
At the end of the battery life, the batteries gradually lose electric capacity.
When your batteries are fully charged, the tenth bar (far right) illuminates on the battery-discharge indicator (Figure 13).
As you use the machine, the bars disappear as the electrical capacity of the batteries is used.
When only the second bar from the left remains on the battery-discharge indicator, it is a good time to charge (Figure 14).
If you continue to use the machine with only 2 bars remaining, bars 1 and 2 alternately flash.
Important: When only the second bar from the left remains on the battery-discharge indicator, the machine may enter a reduced-speed mode; this mode aids in protecting the batteries, but prolonged operation in this mode can damage the batteries and/or the machine. Avoid draining your batteries down to the second bar from the left to prevent this issue. Charge the batteries immediately.If the batteries become fully discharged, the machine shuts down. Do not allow the batteries to become fully discharged.
Important: To obtain maximum battery life, always charge the batteries before the charge reaches the second bar from the left on the screen. Regularly depleting the batteries to lower than the second bar from the left reduces the life of the batteries.
Maintenance Service Interval | Maintenance Procedure |
---|---|
After the first 100 hours |
|
Perform the breaking in a new machine guidelines to provide proper performance and long life for the machine.
Check the brake fluid and the water level in the batteries regularly.
Avoid hard braking situations for the first several hours of new machine break-in operation. New brake linings may not be at optimum performance until several hours of use has caused the brakes to become burnished (broken-in); refer to Burnishing the Brakes.
Refer to for any special, low-hour checks.
Check the front suspension positioning and adjust it, if necessary; refer to Adjusting the Front Wheel Alignment.
The owner/operator can prevent and is responsible for accidents that may cause personal injury or property damage.
Passengers should sit in the designated seating positions only. Do not carry passengers in the cargo bed. Keep bystanders and pets away from the machine during operation.
Wear appropriate clothing, including eye protection; long pants; substantial, and slip-resistant footwear. Tie back long hair and do not wear loose clothing or loose jewelry.
Use your full attention while operating the machine. Do not engage in any activity that causes distractions; otherwise, injury or property damage may occur.
Do not operate the machine while ill, tired, or under the influence of alcohol or drugs.
Do not exceed the maximum gross vehicle weight (GVW) of the machine.
Use extra caution when operating, braking, or turning the machine with a heavy load in the cargo bed.
Carrying oversized loads in the cargo bed reduces the stability of the machine. Do not exceed the carrying capacity of the bed.
Carrying material that cannot be bound to the machine adversely affects the steering, braking, and stability of the machine. When you carry material that cannot be bound to the machine, use caution when steering or braking.
Carry a reduced load and reduce the ground speed of the machine when operating on rough, uneven terrain, and near curbs, holes, and other sudden changes in terrain. Loads may shift, causing the machine to become unstable.
Before you start the machine, ensure that the transmission is in neutral, the parking brake is engaged, and you are in the operating position.
You and your passengers should remain seated whenever the machine is moving. Keep your hands on the steering wheel; your passengers should use the handholds provided. Keep arms and legs within the machine body at all times.
Operate the machine only in good visibility. Watch for holes, ruts, bumps, rocks, or other hidden objects. Uneven terrain could overturn the machine. Tall grass can hide obstacles. Use care when approaching blind corners, shrubs, trees, or other objects that may obscure your vision.
Do not drive the machine near drop-offs, ditches, or embankments. The machine could suddenly roll over if a wheel goes over the edge or if the edge gives way.
Always watch out for and avoid low overhangs such as tree limbs, door jambs, overhead walkways, etc.
Look behind and down before reversing the machine to be sure of a clear path.
When using the machine on public roads, follow all traffic regulations and use any additional accessories that may be required by law, such as lights, turn signals, slow-moving vehicle (SMV) signs, and others as required.
If the machine ever vibrates abnormally, stop and shut off the machine immediately, wait for all movement to stop, and inspect for damage. Repair all damage to the machine before resuming operation.
It can take longer to stop the machine on wet surfaces than on dry surfaces. To dry out wet brakes, drive slowly on level ground while putting light pressure on the brake pedal.
Operating the machine at high speed and then quickly stopping may cause the rear wheels to lock up, which impairs your control of the machine.
Do not touch the motor while the motor is running, or soon after you turn off the motor, because these areas may be hot enough to cause burns.
Do not leave a running machine unattended.
Before you leave the operating position, do the following:
Park the machine on a level surface.
Move the direction selector to the NEUTRAL position.
Engage the parking brake.
Shut off the machine and remove the key.
Wait for all movement to stop.
Do not operate the machine when there is the risk of lightning.
Use accessories and attachments approved by The Toro® Company only.
Do not exceed the gross vehicle weight (GVW) of the machine. You must account for yourself, your passengers, and the load in the cargo bed contributing to the overall GVW of the machine.
Passengers should sit in the designated seating positions only. Do not allow passengers to sit in the cargo bed.
You and your passengers should remain seated whenever the machine is in motion.
The additional machine length results in a larger turn radius, so allow more space to maneuver the machine.
Note: A 2-post Rollover Protection System (ROPS) is available for this machine as an accessory. Use a ROPS if you will work next to drop-offs, near water, in rough terrain, or on a slope, which could result in a rollover. Contact an authorized Toro distributor for more information.
Slopes are a major factor related to loss-of-control and tip-over accidents, which can result in severe injury or death.
Survey the site to determine which slopes are safe for operating the machine and establish your own procedures and rules for operating on those slopes. Always use common sense and good judgment when performing this survey.
If you feel uneasy operating the machine on a slope, do not do it.
Keep all movement on slopes slow and gradual. Do not suddenly change the speed or direction of the machine.
Avoid operating the machine on wet terrain. Tires may lose traction. A rollover can occur before the tires lose traction.
Travel straight up and down a slope.
If you begin to lose momentum while climbing a slope, gradually engage the brakes and slowly reverse the machine straight down the slope.
Turning while going up or down a slope can be dangerous. If you must turn on a slope, do it slowly and cautiously.
Heavy loads affect stability on a slope. Carry a reduced load and reduce your ground speed when operating on a slope or if the load has a high center of gravity. Secure the load to the cargo bed of the machine to prevent the load from shifting. Take extra care when hauling loads that shift easily (e.g., liquids, rock, sand, etc.).
Avoid starting, stopping, or turning the machine on a slope, especially with a load. Stopping while going down a slope takes longer than stopping on level ground. If you must stop the machine, avoid sudden speed changes, which can cause the machine to tip or roll over. Do not engage the brakes suddenly when rolling rearward, as this may cause the machine to overturn.
Do not exceed the gross vehicle weight (GVW) of the machine when operating it with a load in the cargo bed and/or towing a trailer; refer to Specifications.
Distribute the load in the cargo bed evenly to improve the stability and control of the machine.
Before dumping, ensure that there is no one behind the machine.
Do not dump a loaded cargo bed while the machine is sideways on a slope. The change in weight distribution may cause the machine to overturn.
A raised bed could fall and injure persons that are working beneath it.
Always use the prop rod to hold the bed up before working under the bed.
Remove any load material from the bed before raising it.
Driving the machine with the cargo bed raised could cause the machine to tip or roll easier. You could damage the structure of the cargo bed if you operate the machine with the bed raised.
Operate the machine when the cargo bed is down.
After emptying the cargo bed, lower it.
If a load is concentrated near the back of the cargo bed when you release the latches, the bed may unexpectedly tip open, injuring you or bystanders.
Center loads in the cargo bed, if possible.
Hold the cargo bed down and ensure that no one is leaning over the bed or standing behind it when releasing the latches.
Remove all cargo from the bed before lifting the bed up to service the machine.
The weight of the bed may be heavy. Hands or other body parts could be crushed.
Keep your hands and other body parts away when lowering the bed.
If you unloaded loose material such as sand, landscaping rock, or wood chips from the cargo bed of the machine, some of the material that you unloaded may have lodged in the hinge area of the tailgate. Perform the following steps before closing the tailgate.
Use your hands to remove as much of the material from the hinge area as possible.
Rotate the tailgate to approximately the 45° position (Figure 18).
Use a short, shaking motion to rotate the tailgate back and forth several times (Figure 18).
Note: This action helps move material away from the hinge area.
Lower the tailgate and check for material remaining in the hinge area.
Repeat steps 1 through 4 until the material is removed from the hinge area.
Rotate the tailgate up and lift the tailgate into the notches in the cargo bed.
Use the rear cargo bed accessory mount to attach accessories to the rear of the machine.
Capacity: 45 kg (100 lb)
Loosen the “T” handle by rotating it clockwise (Figure 19).
Insert your accessory into the receiver until the holes align (Figure 19).
Secure the assembled accessory to the receiver tube using the clevis pin and hairpin cotter supplied with the accessory.
Tighten the “T” handle by rotating it counterclockwise (Figure 20).
Important: When stopping the machine on an incline, use the service brakes to stop the machine and engage the parking brake to hold the machine in place. Using the accelerator to stall the machine on the hill can overheat the motor or drain the batteries.
Remove your foot from the accelerator pedal.
Slowly press the brake pedal to apply the service brakes until the machine comes to a complete stop.
Note: The stopping distance may vary depending on the machine load and speed.
Use the following guidelines when loading the cargo bed and operating the machine:
Observe the weight capacity of the machine and limit the weight of the load that you carry in the cargo bed as described in Specifications and on the gross vehicle weight tag of the machine.
Note: The load rating is specified for machine operation on a level surface only.
Reduce the weight of the load that you carry in the cargo bed when operating the machine on hills and rough terrain.
Reduce the weight of the load that you carry when the materials are tall (and have a high center of gravity), such as a stack of bricks, landscaping timbers, or fertilizer bags. Distribute the load as low as possible to ensure that the load does not reduce your ability to see behind the machine when operating it.
Keep loads centered by loading the cargo bed as follows:
Evenly position the weight in the cargo bed from side to side.
Important: Tipping over is more likely to occur if the cargo bed is loaded to 1 side.
Evenly position the weight in the cargo bed from front to back.
Important: Loss of steering control or the machine may tip over if you position the load behind the rear axle and the traction on the front tires is reduced.
Use extra caution when transporting oversized loads in the cargo bed, particularly when you cannot center the weight of the oversize load to the cargo bed.
Whenever possible, secure the load by binding it to the cargo bed so that it does not shift.
When transporting liquids, use caution when driving the machine uphill or downhill, when suddenly changing speed or stopping, or when driving over rough surfaces.
The capacity of the cargo bed is 0.28 m3 (10 ft3). The amount (volume) of material that you can place in the bed without exceeding the load ratings of the machine can vary greatly depending on the density of the material.
Refer to the following table for load volume limits with various materials:
Material | Density | Maximum Cargo Bed Capacity(on level ground) |
Gravel, dry | 1522 kg/m3 (95 lb/ft3) | Full |
Gravel, wet | 1922 kg/m3 (120 lb/ft3) | 3/4 Full |
Sand, dry | 1442 kg/m3 (90 lb/ft3) | Full |
Sand, wet | 1922 kg/m3 (120 lb/ft3) | 3/4 Full |
Wood | 721 kg/m3 (45 lb/ft3) | Full |
Bark | <721 kg/m3 (<45 lb/ft3) | Full |
Earth, packed | 1602 kg/m3 (100 lb/ft3) | 3/4 Full (approximately) |
Before you leave the operating position, do the following:
Park the machine on a level surface.
Move the direction selector to the NEUTRAL position.
Engage the parking brake.
Shut off the machine and remove the key.
Wait for all movement to stop.
Allow the machine to cool before adjusting, servicing, cleaning, or storing it.
Do not store the machine where there is an open flame, spark, or pilot light, such as on a water heater or other appliance.
Keep all parts of the machine in good working condition and all hardware tightened.
Maintain and clean the seat belt(s) as necessary.
Replace all worn, damaged, or missing decals.
Use care when loading or unloading the machine into a trailer or a truck.
Use full-width ramps for loading the machine into a trailer or a truck.
Tie the machine down securely.
Refer to Figure 21 and Figure 22 for the tie-down locations on the machine.
Note: Load the machine on the trailer with the front of the machine facing forward. If that is not possible, secure the machine hood to the frame with a strap, or remove the hood and transport and secure it separately or the hood may blow off during transport.
Loose seats may fall off the machine and trailer when transporting the machine, and the seats may land on another machine or obstruct the roadway.
Remove the seats or ensure that the seats are secured by the pivot pins.
In case of an emergency, you can tow the machine for a short distance; however, this should not be a standard operating procedure.
Towing at excessive speeds could cause a loss of steering control, resulting in personal injury.
Never tow the machine at faster than 8 km/h (5 mph).
Towing the machine is a 2-person job. If you must move the machine a considerable distance, transport it on a truck or trailer; refer to Towing a Trailer.
Shut off the machine and remove the key.
Important: If you tow the machine with the key in the ON position, the electrical system may be damaged.
Affix a tow line to the tongue at the front of the machine’s frame (Figure 21).
Disengage the parking brake.
The machine is capable of pulling trailers. Tow hitches are available for the machine, contact your authorized Toro distibutor for details.
When hauling cargo or towing a trailer, do not overload your machine or trailer. Overloading either the machine or the trailer can cause poor performance or damage to the brakes, axle, motor, transaxle, steering, suspension, body structure, or tires.
Always load a trailer with 60% of the cargo weight in the front of the trailer. This places approximately 10% of the gross trailer weight (GTW) on the tow hitch of the machine.
To provide adequate braking and traction, always load the cargo bed when using a trailer. Do not exceed the GTW or GVW limits.
Avoid parking a machine with a trailer on a hill. If you must park on a hill, engage the parking brake and block the tires of the trailer.
Note: The procedures in this section show a machine with a plastic cargo bed and bucket seat; for additional procedures for other attachments, refer to the Maintenance section (if applicable) in the Installation Instructions. Visit www.Toro.com for your instructions or scan the QR code (if applicable) on your attachment.
Do not allow untrained personnel to service the machine.
Before you leave the operating position, do the following:
Park the machine on a level surface.
Move the direction selector to the NEUTRAL position.
Engage the parking brake.
Shut off the machine and remove the key.
Wait for all movement to stop.
Allow the machine to cool before adjusting, servicing, cleaning, or storing it.
Support the machine with jack stands whenever you work under the machine.
Do not work under a raised bed without the proper bed safety support in place.
Do not charge the batteries while servicing the machine.
To ensure that the entire machine is in good condition, keep all hardware properly tightened.
To reduce the potential fire hazard, keep the machine area free of excessive grease, grass, leaves, and accumulation of dirt.
If possible, do not perform maintenance while the machine is running. Keep away from moving parts.
If you must run the machine to perform a maintenance adjustment, keep your hands, feet, clothing, and any parts of the body away from any moving parts. Keep bystanders away from the machine.
Check the parking brake operation as recommended in the maintenance schedule and adjust and service it as required.
Keep all parts of the machine in good working condition and all the hardware properly tightened. Replace all worn or damaged decals.
Never interfere with the intended function of a safety device or reduce the protection provided by a safety device.
If major repairs are ever necessary or assistance is required, contact an authorized Toro distributor.
Altering this machine in any manner may affect the operation of the machine, performance, durability, or its use may result in injury or death. Such use could void the product warranty of The Toro® Company.
Maintenance Service Interval | Maintenance Procedure |
---|---|
After the first 100 hours |
|
Before each use or daily |
|
Every 25 hours |
|
Every 100 hours |
|
Every 300 hours |
|
Every 400 hours |
|
Every 800 hours |
|
Every 1,000 hours |
|
Note: Download a free copy of the electrical schematic by visiting www.Toro.com and searching for your machine from the Manuals link on the home page.
Failure to properly maintain the machine could result in premature failure of machine systems, causing possible harm to you or bystanders.
Keep the machine well maintained and in good working order as indicated in these instructions.
Important: If the machine is subjected to any of the conditions listed below, perform maintenance twice as frequently:
Desert operation
Cold climate operation—below 10°C (50°F)
Trailer towing
Frequent operation in dusty conditions
Construction work
After extended operation in mud, sand, water, or similar dirty conditions, do the following:
Have your brakes inspected and cleaned as soon as possible. This prevents any abrasive material from causing excessive wear.
Wash the machine using water alone or with a mild detergent.
Important: Do not use brackish or reclaimed water to clean the machine.
Raise the cargo bed before performing maintenance. A raised cargo bed can fall and injure persons that are underneath it.
Always use the prop rod to hold the cargo bed up before working underneath it.
Remove any load material from the cargo bed before working underneath it.
Park the machine on a level surface.
Move the direction selector to the NEUTRAL position.
Engage the parking brake.
Shut off the machine and remove the key.
Empty and raise the cargo bed.
The machine may be unstable when using a jack. The machine could slip off the jack, injuring anyone beneath it.
Do not start the machine while the machine is on a jack.
Always remove the key from the key switch before getting off the machine.
Block the tires when the machine is supported by lifting equipment.
Use jack stands to support the machine once you have lifted it.
Important: Whenever you run the machine for routine maintenance and/or diagnostics, ensure that the rear wheels of the machine are 25 mm (1 inch) off the ground, with the rear axle supported on jack stands.
The lifting point at the front of the machine is located at the front of the frame, behind the towing tongue (Figure 23).
The lifting point at the rear of the machine is located under the axle tubes (Figure 24).
Slide the seat assembly onto the pins and lower the seat assembly (Figure 28).
Push the bench cushion forward to the raised position.
Slide the cushion to the side, out of the pins, and lift the cushion upward (Figure 29).
Slide the bench cushion onto the pins and lower the cushion (Figure 30).
Maintenance Service Interval | Maintenance Procedure |
---|---|
Every 300 hours |
|
Grease specification: Mobilgrease XHP™-222
Lift the front of the machine and support it with jack stands.
Remove the 4 lug nuts that secure the wheel to the hub (Figure 31).
Remove the flange-head bolts (3/8 x 3/4 inch) that secure the bracket for the brake assembly to the spindle and separate the brake from the spindle (Figure 32).
Note: Support the brake assembly before proceeding to the next step.
Remove the dust cap from the hub (Figure 33).
Remove the cotter pin and nut retainer from the spindle and spindle nut (Figure 33).
Remove the spindle nut from the spindle, and separate the hub and rotor assembly from the spindle (Figure 33 and Figure 34).
Wipe clean the spindle with a rag.
Repeat steps 1 through 7 to the hub and rotor at the other side of the machine.
Remove the outboard bearing and bearing race from the hub (Figure 35).
Remove the seal, inboard bearing from the hub (Figure 35).
Wipe clean the seal and check for wear and damage.
Note: Do not use cleaning solvent to clean the seal. Replace the seal if it is worn or damaged.
Clean the bearings and races, and check these parts for wear and damage.
Note: Replace all worn or damaged parts. Ensure that the bearings and races are clean and dry.
Clean the cavity of the hub of all grease, dirt, and debris (Figure 35).
Pack the bearings with the specified grease.
Fill the cavity of hub 50 to 80% full of the specified grease (Figure 35).
Assemble the inboard bearing onto the race at the inboard side of the hub and install the seal (Figure 35).
Repeat steps 1 through 8 to the bearings for the other hub.
Apply a light coat of the specified grease to the spindle (Figure 36).
Assemble the hub and rotor onto the spindle with the rotor inboard (Figure 36).
Assemble the outboard bearing onto the spindle and seat the bearing to the outboard race (Figure 36).
Assemble the tab washer onto the spindle (Figure 36).
Thread the spindle nut onto the spindle and tighten the nut to 15 N∙m (11 ft-lb), while rotating the hub to seat the bearing (Figure 36).
Loosen the spindle nut until the hub rotates freely.
Torque the spindle nut to 170 to 225 N∙cm (15 to 20 in-lb).
Install the retainer over the nut and check the alignment of the slot in the retainer and the hole in the spindle for the cotter pin (Figure 37).
Note: If the slot in the retainer and the hole in the spindle are not aligned, tighten the spindle nut to align the slot and hole to a maximum torque of 226 N∙cm (20 in-lb) on the nut.
Install the cotter pin and bend each legs around the retainer (Figure 37).
Install the dust cap onto the hub (Figure 37).
Repeat steps 1 through 10 for the hub and rotor at the other side of the machine.
Clean the 2 flange-head bolts (3/8 x 3/4 inch) and apply a coat of medium-strength thread-locking compound to the threads of the bolts.
Align the brake pads to either side of the rotor (Figure 32) and the holes in the caliper bracket with the holes in the brake mount of the spindle frame (Figure 36).
Secure the caliper bracket to the spindle frame (Figure 32) using the 2 flange-head bolts (3/8 x 3/4 inch).
Torque the 2 flange-head bolts to 47 to 54 N∙m (35 to 40 ft-lb).
Align the holes in the wheel to the studs of the hub and assemble the wheel to the hub with the valve stem outward (Figure 31).
Note: Ensure that the mounting surface of the wheel is flush with the hub.
Secure the wheel to the hub using the lug nuts (Figure 31).
Torque the lug nuts to 108 to 122 N∙m (80 to 90 ft-lb).
Repeat steps 1 through 5 for the brake and wheel on the other side of the machine.
Disconnect the battery before repairing the machine. Disconnect the negative terminal first and the positive last. Connect the positive terminal first and the negative last.
Charge the battery in an open, well-ventilated area, away from sparks and flames. Unplug the charger before connecting or disconnecting the battery. Wear protective clothing and use insulated tools.
To reduce the potential for fire, keep the batteries and motor area free of excessive grease, grass, leaves, and accumulation of dirt.
Remove all jewelry and watches before servicing the batteries.
Do not charge the batteries while servicing the machine.
Always disconnect all the battery cables before servicing any electrical components; refer to Disconnecting the Batteries.
Note: Disconnecting all the battery cables isolates power from the electrical system.
Battery electrolyte contains sulfuric acid, which produces hydrogen, a gas that is explosive in certain conditions. Sulfuric acid can burn skin and damage clothing; when emitted in gas form, it can damage your lungs.
Always service, store, and charge the machine in a well-ventilated area.
Keep sparks and open flames away from the batteries.
Do not smoke near the batteries.
Do not use an open flame to check the level or leakage of battery electrolyte.
Wear proper eye, hand, and face protection.
Do not lean over the batteries at any time.
Avoid breathing in battery fumes.
Fill the batteries where clean water is always available for flushing the skin.
If you get electrolyte on your skin or eyes, flush the affected area for 20 minutes with clean water. Remove affected clothing. Seek medical attention immediately.
Keep children and pets away from the batteries and electrolyte.
Electrolyte is poisonous.
Do not drink the electrolyte.
If electrolyte has been swallowed, have them drink large quantities of water immediately to dilute the electrolyte, if possible.
Do not attempt to make them vomit.
Call a poison control center and get medical attention immediately.
When not filling the batteries, keep the battery vent caps tight on the batteries. Do not operate the machine if any of the vent caps are missing or damaged.
When removing or installing the batteries, do not allow the battery terminals to touch any metal parts of the machine.
Do not allow metal tools to short between the battery terminals and metal parts of the machine.
Do not check a battery charge by placing a metal object across the posts. This causes sparks, which can cause an explosion.
Always keep the battery retainers in place to protect and secure the batteries.
Read and understand the charging instructions before charging the batteries; refer to Charging the Batteries. Also, take the following precautions when charging the batteries:
Turn the machine key switch to OFF before connecting the charger to a power source.
Use only the battery charger supplied with the machine to charge the batteries.
Do not charge a damaged or frozen battery.
Always unplug the AC power cord from the power outlet before unplugging it from the machine charging receptacle to avoid sparks.
If a battery gets hot while charging, begins emitting large amounts of gasses, or spews electrolyte, immediately disconnect the charger power cord from the power outlet. Have the machine serviced by an Authorized Service Dealer before using it again.
Raise the seat assembly and raise the cargo bed before maintaining the batteries; refer to Raising and Lowering the Seat Assembly and Raising the Cargo Bed to the Dump Position.
Battery terminals or metal tools could short against metal components causing sparks. Sparks can cause the battery gases to explode, resulting in personal injury.
When removing or installing the battery, do not allow the battery terminals to touch any metal parts of the machine.
Do not allow metal tools to short between the battery terminals and metal parts of the machine.
Use insulated tools when maintaining the batteries.
Always keep the battery retainers in place to protect and secure the batteries.
Do not touch any electrical components or contacts on the motor.
Touching any of these components or contacts could seriously injure you or cause death.
Maintenance Service Interval | Maintenance Procedure |
---|---|
Every 25 hours |
|
Ensure that all the battery caps are tight.
Use a paper towel to clean the batteries.
If the battery terminals are corroded, clean them with a solution of 4 parts water and 1 part baking soda. Also, clean the posts and cable clamps with a post and clamp cleaner.
Note: The posts and clamps should have a bright, metallic shine.
Apply a light coating of Toro battery-terminal protector.
Maintenance Service Interval | Maintenance Procedure |
---|---|
Before each use or daily |
|
The charger for this machine is located inside the machine under the operator’s seat. For maximum battery life, charge the batteries whenever you are not using the machine. Depending on how discharged the batteries are and the ambient temperature of the batteries, it may take up to 16 hours to charge the batteries to full capacity.
Note: Normal charge time is approximately 8 to 10 hours.
Important: Lead-acid batteries do not develop a charge memory and do not need to be fully discharged before charging them. Fully discharging the batteries may damage them. Charge the batteries any time the machine is not in use.
Charging the battery produces gases that can explode.
Never smoke near the batteries and keep sparks and flames away from them.
Position the machine in a well-ventilated area near a suitable power outlet.
Check the electrolyte level of the batteries.
Note: After fully charging the batteries, fill the batteries with distilled or deionized water; refer to Adding Distilled or Deionized Water to the Batteries.
Important: Fully charge the batteries before adding the water to the batteries. While charging, the electrolyte increases in volume, and filling a low battery before fully charging the batteries can cause the electrolyte to overflow and leak out of the vent.
Connect a 16 gauge (or larger diameter), 2.5 m (8.2 ft) or shorter charger cord to the charging receptacle on the machine (Figure 38).
Note: Ensure that the charger-voltage setting matches the voltage at the power outlet being used.
Note: In high-ambient temperature environments, remove the seat assembly for optimal charging time; refer to Removing a Bucket Seat. If the battery charger is too hot, it may not charge properly. In cold temperatures, it may take a longer for the batteries to charge.
Plug the charger power cord into the power outlet.
Note: While the batteries are charging, the green light on the charger blinks on and off. When the batteries are fully charged, the green light stops blinking and stays on.
Disconnect the cord from the power outlet.
Disconnect the charger from the machine.
Refer to the following table and Figure 38 for information on the meanings of the varying colors of the charger-status light.
Charger-Status Light Color | Solid/Flashing | Meaning |
Green | Solid | Charging complete |
Green | Flashing | Short flash—less than 80% chargeLong flash—greater than 80% charge |
Amber | Flashing | Reduced-power mode—low AC voltage or high internal charger temperature; charge immediately |
Red | Flashing | Charger error—reset the charger powerIf this error persists, refer to the blink codes in the charger manual |
Maintenance Service Interval | Maintenance Procedure |
---|---|
Before each use or daily |
|
Park the machine on a level surface, engage the parking brake, shut off the machine, remove the key, and raise cargo bed; Raising the Cargo Bed to the Dump Position.
Raise the seat assembly to access the batteries; refer to Raising and Lowering the Seat Assembly.
Check the eyelets on each of the batteries to see if they are either black or white (Figure 39).
Note: Black eyelets indicate that the batteries are full of water. White eyelets indicate that water is needed for the batteries.
If the eyelets are white, you must add distilled or deionized water to the batteries; refer to Adding Distilled or Deionized Water to the Batteries.
Maintenance Service Interval | Maintenance Procedure |
---|---|
Every 25 hours |
|
Important: Fully charge the batteries before adding the water to the batteries. While charging, the electrolyte increases in volume, and filling a low battery before fully charging the batteries can cause the electrolyte to overflow and leak out of the vent.
Important: Use only clean, distilled or deionized water to fill the batteries. Using tap water may damage and reduce the life of the batteries.
Park the machine on a level surface, engage the parking brake, shut off the machine, remove the key, and raise cargo bed; Raising the Cargo Bed to the Dump Position.
Charge the batteries until a full charge is achieved; refer to Charging the Batteries.
Raise the seat assembly to access the batteries; refer to Raising and Lowering the Seat Assembly.
Connect your Toro water hand pump to the water-fill port (Figure 40).
Pump water into the batteries until all the eyelets on top of the batteries are black, indicating that they are filled with water.
Important: Do not overfill the battery. Electrolyte will overflow onto other parts of the machine and severe corrosion and deterioration may result. Also, overfilling the battery may reduce the life of the battery.
When the machine begins to lose operating range or when the length of time to discharge or charge the battery is significantly reduced, the batteries are probably wearing and losing their ability to hold a charge. Take the machine to an Authorized Service Dealer and have them test the batteries to determine whether the batteries need to be replaced. The dealer can then replace the batteries for you. If you wish to replace the batteries yourself, use the following procedures:
Raise the cargo bed, turn the key switch to the OFF position, and remove the key.
Disconnect the main negative-battery cable (black) that connects the bank of batteries to the ground point of the machine (Figure 41).
Note: The main battery cables are long when compared to battery-interconnect cables.
Disconnect the main positive-battery cable (red) that connects the bank of batteries to the main contactor of the machine (Figure 41).
Remove all of the battery-interconnect cables from the batteries.
Remove the battery retainers located between the batteries.
Remove all of the batteries and recycle them according to your local codes.
Assemble new batteries into the machine at the locations from where you removed batteries in step 3.
Note: Pay attention to the battery polarity when installing the new batteries (Figure 41).
Install the battery retainers and tighten the nuts until the retainer securely grips the batteries.
Connect the batteries together as shown in Figure 41 with the battery-interconnect cables that you removed in step 1.
Ensure that the battery terminals are clean and free of oxidation.
Connect the main positive-battery cable (red) between the bank of batteries and the machine (Figure 41).
Connect the main negative-battery cable (black) between the bank of batteries and the machine (Figure 41).
Torque the nuts securing all of the battery cables until the retainer securely grips the battery.
Coat the battery terminals with Toro battery-terminal protector.
Ensure that the rubber boots on each battery cable are securely seated over the battery terminals.
Insert the key into the key switch and rotate the switch to the ON position.
Lower the cargo bed, rotate the key switch to the OFF position, and remove the key.
Charge the batteries fully before placing the machine into storage. Plug the charger into a wall outlet while the machine and batteries are in storage. Leave the charger plugged into a wall outlet and charging receptacle during storage to ensure that the batteries stay charged and do not freeze; otherwise, charge the batteries at least once a month.
Important: If the machine cannot be plugged in during storage, fully charge the batteries at least once a month. The batteries self-discharge over long periods of time, which may damage the batteries to the point of being unusable, even if the batteries are new.
There are 4 fuses in the electrical system; the other slots are open for options. They are located under the seat assembly behind a battery on the right side of the machine (Figure 42).
Main power | 10 A |
Electric relay | 20 A |
USB power point | 5 A |
Headlights | 10 A |
Optional lift kit—open | 15 A |
Horn | 30 A |
Disconnect the batteries; refer to Disconnecting the Batteries.
Open the hood.
Disconnect the electrical connector for the harness from the connector of the lamp assembly (Figure 43).
Remove the speed clips that secure the headlight to the headlight bracket (Figure 43).
Note: Retain all parts for installation of the new headlight.
Remove the headlight assembly by moving it forward through the opening in the front bumper (Figure 43).
Install the new headlight through the opening in the bumper (Figure 43).
Note: Ensure the adjustment posts are lined up with the holes in the mounting bracket behind the bumper.
Secure the headlight assembly with the speed clips that you removed in step 4.
Connect the electrical connector for the harness to the connector of the lamp assembly (Figure 43).
Adjust the headlights to direct the beams to the desired position, refer to Adjusting the Headlights.
Use the following procedure to adjust the headlight beam position whenever a headlight assembly is replaced or removed.
Park the machine on a level surface with the headlights approximately 7.6 m (25 ft) from a wall (Figure 44).
Measure the distance from the floor to the center of the headlight and make a mark on the wall at the same height.
Turn the key switch to the ON position, and turn on the headlights.
Take note of where the headlights aim on the wall.
The brightest part of the headlight beam should be 20 cm (8 inches) below the mark placed on the wall (Figure 44).
At the back of the headlight assembly, rotate adjustment screws (Figure 43) to pivot the headlight assembly and align the position of the cast beam.
Connect the batteries and close the hood; refer to Connecting the Batteries.
Maintenance Service Interval | Maintenance Procedure |
---|---|
Every 100 hours |
|
Inspect the tires and rims for signs of wear and damage.
Note: Operating accidents, such as hitting curbs, can damage a tire or rim and also disrupt wheel alignment, so inspect tire condition after an accident.
Torque the wheel lug nuts to 108 to 122 N∙m (80 to 90 ft-lb).
Maintenance Service Interval | Maintenance Procedure |
---|---|
Every 100 hours |
|
With the steering wheel at the centered position (Figure 45), turn the steering wheel to the left or right. If you turn the steering wheel more than 13 mm (1/2 inch) to the left or right, and the tires do not turn, check the following steering and suspension components to ensure that they are not loose or damaged:
Steering shaft to the steering-rack assembly joint
Important: Inspect the condition and security of the pinion-shaft seal (Figure 46).
Steering-rack assembly tie rods
Maintenance Service Interval | Maintenance Procedure |
---|---|
Every 100 hours |
|
Check the tire pressure to ensure that the front tires are inflated to 82 kPa (12 psi).
Either add weight to the driver's seat equal to the average operator who will run the machine, or have an operator sit on the seat. The weight or operator must remain on the seat for the duration of the adjustment procedure.
On a level surface, roll the machine straight back 2 to 3 m (6 to 10 ft) and then straight forward to the original starting position. This allows the suspension to settle into the operating position.
Owner provided tools: spanner wrench, Toro Part 132-5069; refer to your authorized Toro distributor.
Important: Make the camber adjustments only if you are using a front attachment or if there is uneven tire wear.
Check the camber alignment at each wheel; the alignment should be as close to neutral (zero) as possible.
Note: The tires should be aligned with the tread evenly on the ground to reduce uneven wear.
If the wheel camber is out of alignment, use the spanner wrench to rotate the collar on the shock absorber to align the wheel (Figure 47).
Important: Before adjusting toe-in, ensure that the camber adjustment is as close to neutral as possible; refer to Adjusting the Camber.
Measure the distance between both of the front tires at the axle height at both the front and rear of the front tires (Figure 48).
If the measurement does not fall within 0 to 6 mm (0 to 1/4 inch), loosen the jam nuts at the outer end of the tie rods (Figure 49).
Rotate both tie rods to move the front of the tire inward or outward.
Tighten the tie rod jam nuts when the adjustment is correct.
Ensure that there is full travel of the steering wheel in both directions.
Maintenance Service Interval | Maintenance Procedure |
---|---|
Every 100 hours |
|
Park the machine on a level surface.
Engage the parking brake.
Shut off the motor and remove the key.
Remove the fill plug on the transaxle (Figure 50).
Note: The fluid level should be even with the bottom of the fill plug.
If the fluid level is low, remove the fill plug and add the specified fluid until it runs out of the hole (Figure 50).
Install the fill plug and torque it to 20 to 27 N∙m (15 to 20 ft-lb).
Maintenance Service Interval | Maintenance Procedure |
---|---|
Every 100 hours |
|
Every 800 hours |
|
Fluid Type: SAE 10W-30 (API service SJ or higher)
Fluid Capacity: 0.66 L (0.7 US qt)
Align a drain pan under the transaxle cover (Figure 51).
Remove the bolts from the transaxle cover and drain the fluid completely (Figure 51).
Note: Retain the transaxle cover and bolt.
Install the transaxle cover using the previously removed bolts, and torque the bolts to 22 to 32 N∙m (16 to 24 ft-lb).
Remove the fill plug on the transaxle and fill the transaxle with the specified fluid until it runs out of the fill hole (Figure 50).
Install the fill plug and torque it to 20 to 27 N∙m (15 to 20 ft-lb).
Engage the parking brake by pulling the parking-brake lever toward you, until you feel tension.
If you do not feel tension when pulling the parking-brake toward you within 11.4 to 16.5 cm (4-1/2 to 6-1/2 inches) from the “P” symbol on the dash, then you need to adjust the parking brake; refer to Adjusting the Parking Brake.
Ensure that the parking brake is disengaged.
Using jack stands, lift the rear of the machine; refer to Lifting the Machine.
Using 2 wrenches, hold the adjusting post on the caliper in place with 1 wrench, and loosen the jam nut 1/4 turn with the other wrench (Figure 52).
While holding the adjusting post and the jam nut in place, turn the adjusting post in to tighten (Figure 52).
Note: Perform this step until you feel drag on the wheel.
While holding the adjusting post and the jam nut in place, back off 1/4 turn (Figure 52).
While holding the adjusting post and the jam nut in place, tighten the jam nut (Figure 52).
Perform steps 1 through 6 to the other side.
Verify that the parking brake is adjusted to the proper tension; refer to Checking the Parking Brake.
Note: If you cannot adjust the parking brake to the required tension, the brake pads may be worn and need to be replace. Contact your authorized Toro distributor for assistance.
Maintenance Service Interval | Maintenance Procedure |
---|---|
Before each use or daily |
|
Brake Fluid Type: DOT 3
Park the machine on a level surface, engage the parking brake, shut off the machine, and remove the key.
Raise the hood to gain access to the master-brake cylinder and reservoir (Figure 53).
Look at the outline of the fluid level at the side of the reservoir (Figure 54).
Note: The level should be above the Minimum line.
If the fluid level is low, perform the following:
Close the hood of the machine.
Maintenance Service Interval | Maintenance Procedure |
---|---|
Every 100 hours |
|
Important: Brakes are a critical safety component of the machine. Closely inspect them at the recommended service interval to ensure optimum performance and safety.
Inspect the brake lining for wear or damage. If the lining (brake pad) thickness is less than 1.6 mm (1/16 inch), replace the brake lining.
Inspect the backing plate and other components for signs of excessive wear or deformation. Replace any deformed components.
Check the brake-fluid level; refer to Checking the Brake-Fluid Level.
Maintenance Service Interval | Maintenance Procedure |
---|---|
Every 400 hours |
|
Contact your authorized Toro distributor to inspect and possibly replace the service and parking-brake pads.
Maintenance Service Interval | Maintenance Procedure |
---|---|
Every 1,000 hours |
|
Contact your authorized Toro distributor.
If the cargo-bed latch is out of adjustment, the cargo bed vibrates up and down as you drive the machine. You can adjust the latch posts to make the latches hold the cargo bed snugly to the chassis.
Verify that the cargo bed is latching.
Note: If the cargo bed does not latch, the bed-latch striker is likely too low. If the cargo bed latches, but vibrates up and down as you drive, the bed-latch striker is likely too high.
Raise the cargo bed; Raising the Cargo Bed to the Dump Position.
Loosen the 2 bolts on the bed-latch striker and move the striker up or down, depending on if the striker is too high or too low (Figure 55).
Tighten the 2 bolts on the bed-latch striker (Figure 55).
Verify that the adjustment is correct by latching the cargo bed several times.
Maintenance Service Interval | Maintenance Procedure |
---|---|
Before each use or daily |
|
Wash the machine as needed using water alone or with a mild detergent. You may use a rag when washing the machine.
Important: Do not use brackish or reclaimed water to clean the machine.
Important: Pressurized water is not recommended when washing the machine. It may damage the electrical system, loosen important decals, or wash away necessary grease at friction points. Avoid excessive use of water, especially near the control panel, motor, motor controller, charger, back of the dashboard, and batteries.
Shut off the machine, remove the key, and wait for all movement to stop before you leave the operator’s position. Allow the machine to cool before adjusting, servicing, cleaning, or storing it.
Do not store the machine or fuel container where there is an open flame, spark, or pilot light, such as on a water heater or other appliance.
Park the machine on a level surface, engage the parking brake, shut off the machine, and remove the key.
Clean dirt and grime from the entire machine, including the outside of the motor housing.
Important: You can wash the machine with mild detergent and water. Do not use high pressure water to wash the machine. Pressure washing may damage the electrical system or wash away necessary grease at friction points. Avoid excessive use of water, especially near the control panel, lights, motor, and the battery.
Inspect the brakes; refer to Inspecting the Brakes.
Check the tire pressure; refer to Checking the Tire Pressure.
Check and tighten all bolts, nuts, and screws. Repair or replace any part that is damaged.
Paint all scratched or bare metal surfaces.
Note: Paint is available from your Authorized Service Dealer.
Store the machine in a clean, dry garage or storage area.
Remove the key and put it in a safe place out of the reach of children.
Cover the machine to protect it and keep it clean.
Charge the batteries fully before placing the machine into storage; refer to Charging the Batteries. Plug the charger into a wall outlet while the machine and batteries are in storage. Leave the charger plugged into a wall outlet and charging receptacle during storage to ensure that the batteries stay charged and do not freeze; otherwise, charge the batteries monthly at a minimum.
Plug in the charger during storage to maintain full battery life.
Important: If the machine cannot be plugged in during storage, fully charge the batteries at least once a month. The batteries self-discharge over long periods of time, which may damage the batteries to the point of being unusable, even if the batteries are new.
After fully charging the batteries, fill the batteries with distilled or deionized water before storing; refer to Adding Distilled or Deionized Water to the Batteries.
Problem | Possible Cause | Corrective Action |
---|---|---|
The machine-status light is always illuminated. |
|
|
The machine-status light flashed 1 time. |
|
|
The machine-status light flashed 2 times. |
|
|
The machine-status light flashed 3 times. |
|
|
The machine-status light flashed 4 times. |
|
|
The machine-status light flashed 5 times. |
|
|
The machine-status light flashed 6 times. |
|
|
The machine-status light flashed 7 times. |
|
|
The machine-status light flashed 8 times. |
|
|
The machine-status light flashed 10 times. |
|
|
The machine-status light flashed 11 times. |
|
|
The machine-status light flashed 12 times. |
|
|
The machine-status light flashed 13 times. |
|
|
The machine-status light flashed 14 times. |
|
|
The machine-status light is not illuminated. |
|
|