Z Master® 4000 Series Riding Mower

Before starting the machine each day, perform the Each Use/Daily procedures listed in .

New engines take time to develop full power. Mower decks and drive systems have higher friction when new, placing additional load on the engine. Allow 40 to 50 hours of break-in time for new machines to develop full power and best performance.

The seat can move forward and backward. Position the seat where you have the best control of the machine and are most comfortable (Figure 11).

Figure 11

The MyRide™ suspension system adjusts to provide a smooth and comfortable ride. You can adjust the rear 2-shock assemblies to quickly and easily change the suspension system. Position the suspension system where you are most comfortable.

The slots for the rear-shock assemblies have detent positions for reference. You can position the rear-shock assemblies anywhere in the slot, not just in the detent positions. The following graphic shows the position for a soft or firm ride and the different detent positions (Figure 12).

Figure 12

1. Firmest position
2. Softest position
3. Detents in the slots

Note: Ensure that the left and right rear-shock assemblies are always adjusted to the same positions.

Adjust the rear-shock assemblies (Figure 13).

Figure 13

Use the mower deck as a step to get into the operator’s position (Figure 16).

Figure 16

1. Step here.

Always engage the parking brake when you stop the machine or leave it unattended.

Engaging the Parking Brake

Park the machine on a level surface.

Figure 17

Disengaging the Parking Brake

Figure 18

The blade-control switch (PTO) starts and stops the mower blades and any powered attachments.

Engaging the Blade-Control Switch (PTO)

Note: Engaging the blade-control switch (PTO) with the throttle position at half or less causes excessive wear to the drive belts.

Figure 19

Disengaging the Blade-Control Switch (PTO)

Figure 20

You can move the throttle control between FAST and SLOW positions (Figure 21).

Always use the FAST position when engaging the PTO.

Figure 21

Use the choke to start a cold engine.

1. Pull up the choke knob to engage the choke before using the key switch (Figure 22).

2. Push down the choke knob to disengage the choke after the engine has started (Figure 22).

   

   Figure 22

   1. ON position
   2. OFF position

Note: A warm or hot engine may not require choking.

Important: Do not engage the starter for more than 5 seconds at a time. Engaging the starter motor for more than 5 seconds can damage the starter motor. If the engine fails to start, wait 10 seconds before operating the engine starter again.

Figure 23

The drive wheels turn independently, powered by hydraulic motors on each axle. You can turn 1 side in reverse while you turn the other forward, causing the machine to spin rather than turn. This greatly improves the machine maneuverability but may require some time for you to adapt to how it moves.

The throttle control regulates the engine speed as measured in rpm (revolutions per minute). Place the throttle control in the FAST position for best performance. Always operate in the full throttle position when mowing.

The mower has a hinged grass deflector that disperses clippings to the side and down toward the turf.

1. Push up on the deck-lift switch (Figure 30).

   

   Figure 30

   1. Push up to raise the deck.
   2. Push down to lower the deck.

2. Select a hole in the height-of-cut bracket corresponding to the height of cut desired, and insert the pin (Figure 31).

3. Push down on the deck-lift switch until the height-of-cut linkage slightly contacts the height-of-cut pin (Figure 31).

   Note: Too much contact between the height-of-cut linkage and height-of-cut pin can negatively affect the mower deck height of cut and leveling.

   

   Figure 31

   1. Height-of-cut pin
   2. Height-of-cut linkage
   3. Height-of-cut bracket

Whenever you change the height of cut, adjust the height of the anti-scalp rollers.

Note: Adjust the anti-scalp rollers so that the rollers do not touch the ground in normal, flat mowing areas.

1. Park the machine on a level surface, disengage the blade-control switch and engage the parking brake.

2. Shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position.

3. Adjust the anti-scalp rollers as shown in Figure 32.

   

   Figure 32

   1. Anti-scalp roller
   2. Spacer
   3. Bushing
   4. Flange nut
   5. Bolt

Close the fuel-shutoff valve for transport, maintenance, and storage (Figure 33).

Ensure that the fuel-shutoff valve is open when starting the engine.

Figure 33

1. ON position
2. OFF position

The drive-wheel release valves are located on the left and right sides underneath the engine deck.

1. Park the machine on a level surface, disengage the blade-control switch, and engage the parking brake.

2. Shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position.

3. To push the machine, move both bypass levers forward and lock them into place (Figure 34).

4. Disengage the parking brake before pushing the machine.

5. To run the machine, move the bypass levers rearward and lock them into place (Figure 34).

   

   Figure 34

   1. Bypass lever

Use a heavy-duty trailer or truck to transport the machine. Use a full-width ramp. Ensure that the trailer or truck has all the necessary brakes, lighting, and marking as required by law. Please carefully read all the safety instructions. Knowing this information could help you or bystanders avoid injury. Refer to your local ordinances for trailer and tie-down requirements.

Selecting a Trailer

Warning

Loading a machine onto a trailer or truck increases the possibility of tip-over and could cause serious injury or death (Figure 35).

• Use only a full-width ramp; do not use individual ramps for each side of the machine.

• Do not exceed a 15-degree angle between the ramp and the ground or between the ramp and the trailer or truck.

• Ensure that the length of the ramp is at least 4 times as long as the height of the trailer or truck bed to the ground. This ensures that the ramp angle does not exceed 15 degrees on flat ground.

Figure 35

1. Full-width ramp in stowed position
2. Side view of full-width ramp in loading position
3. Not greater than 15 degrees
4. Ramp is at least 4 times as long as the height of the trailer or truck bed to the ground
5. H=height of the trailer or truck bed to the ground
6. Trailer

Remove the cotter pin to release the mower-deck curtain and get access to the top of the mower deck. After performing maintenance, install the curtain using the previously removed cotter pin.

Loosen the 2 front bolts and remove the sheet-metal guard to access the mower belts and spindles (Figure 38). After performing maintenance, install the sheet-metal guard and tighten the bolts.

Figure 38

1. Sheet-metal guard
2. Bolt

Grease the machine more often in dirty or dusty conditions.

Grease Type: No. 2 lithium or molybdenum grease

1. Park the machine on a level surface, disengage the blade-control switch, and engage the parking brake.

2. Shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position.

3. Clean the grease fittings with a rag.

   Note: Scrape any paint off the front of the fitting(s).

4. Connect a grease gun to the fitting.

5. Pump grease into the fittings until grease begins to ooze out of the bearings.

6. Wipe up any excess grease.

Use light oil or spray lubricant to lubricate the deck-lift pivots.

Figure 39

1. Park the machine on a level surface, disengage the blade-control switch, and engage the parking brake.

2. Shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position.

3. Remove the dust cap and adjust the caster pivots and keep the dust cap off until greasing is done; refer to Greasing the Machine.

4. Remove the hex plug.

5. Thread a grease fitting into the hole.

6. Pump grease into the fitting until it oozes out around the top bearing.

7. Remove the grease fitting from the hole. Install the hex plug and cap.

1. Park the machine on a level surface, disengage the blade-control switch, and engage the parking brake.

2. Shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position.

3. Raise the mower for access.

4. Remove the caster wheel from the caster forks.

5. Remove the seal guards from the wheel hub.

   

   Figure 40

   1. Seal guard
   2. Spacer nut with wrench flats

6. Remove a spacer nut from the axle assembly in the caster wheel.

   Note: Thread-locking compound has been applied to lock the spacer nuts to the axle.

7. Remove the axle (with the other spacer nut still assembled to it) from the wheel assembly.

8. Pry out seals and inspect bearings for wear or damage and replace if necessary.

9. Pack the bearings with a general-purpose grease.

10. Insert 1 bearing and 1 new seal into the wheel.

11. If the axle assembly is missing both spacer nuts, apply a thread-locking compound to 1 spacer nut and thread it onto the axle with the wrench flats facing outward.

    Note: Do not thread the spacer nut all of the way onto the end of the axle. Leave approximately 3 mm (1/8 inch) from the outer surface of the spacer nut to the end of the axle inside the nut.

12. Insert the assembled nut and axle into the wheel on the side with the new seal and bearing.

13. With the open end of the wheel facing up, fill the area inside the wheel around the axle full of general-purpose grease.

14. Insert the second bearing and new seal into the wheel.

15. Apply a thread-locking compound to the second spacer nut, and thread it onto the axle with the wrench flats facing outward.

16. Torque the nut to 8 to 9 N∙m (75 to 80 in-lb), loosen the nut, then torque it to 2 to 3 N∙m (20 to 25 in-lb).

    Note: Make sure that the axle does not extend beyond either nut.

17. Install the seal guards over the wheel hub, and insert the wheel into the caster fork.

18. Install the caster bolt and tighten the nut fully.

Important: To prevent seal and bearing damage, check the bearing adjustment often. Spin the caster tire. The tire should not spin freely (more than 1 or 2 revolutions) or have any side play. If the wheel spins freely, adjust the torque on the spacer nut until there is a slight amount of drag. Apply another layer of thread-locking compound.

Note: Service the air cleaner more frequently if operating conditions are extremely dusty or sandy.

Ensure that the air gap between the center and side electrodes is correct before installing the spark plug. Use a spark plug wrench for removing and installing the spark plug and a gapping tool or feeler gauge to check and adjust the air gap. Install a new spark plug if necessary.

Type of Spark Plug:

Kawasaki FX691 and FX801 engines—NGK^® BPR4ES or equivalent

Air Gap: 0.75 mm (0.030 inch)

Checking the Spark Plug(s)

Important: Do not clean the spark plug(s). Always replace the spark plug(s) when it has a black coating, worn electrodes, an oily film, or cracks.

If you see light brown or gray on the insulator, the engine is operating properly. A black coating on the insulator usually means the air cleaner is dirty.

Set the gap to 0.75 mm (0.03 inch).

Figure 48

Installing the Spark Plug(s)

Figure 49

Important: Install the fuel line hoses and secure with plastic ties the same as they were originally installed at the factory to keep the fuel line away from components that can cause fuel line damage.

Never install a dirty filter after removing it from the fuel line.

The fuel filter is located near the engine on the left front of the engine.

1. Park the machine on a level surface, disengage the blade-control switch (PTO), and engage the parking brake.

2. Shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position.

3. Allow the machine to cool down.

4. Replace the fuel filter (Figure 50).

   Note: Ensure that the flow-direction arrow on the replacement filter points toward the engine.

   

   Figure 50

Do not attempt to drain the fuel tank. Ensure that an Authorized Service Dealer drains the fuel tank and services any components of the fuel system.

The electrical system is protected by fuses. It requires no maintenance; however, if a fuse blows check the component and circuit for a malfunction or short.

The fuses are located on the right console next to the seat (Figure 54).

1. To replace the fuses, pull out the fuse to remove it.

2. Install a new fuse (Figure 54).

   

   Figure 54

   1. Fuse cover
   2. Fuse holder
   3. Fuel-shutoff valve

Inspect the seat belt for wear, cuts, and proper operation of the retractor and buckle. Replace the seat belt if it is damaged.

1. Disengage the blade-control switch (PTO).

2. Drive to an open, flat area and move the motion-control levers to the NEUTRAL-LOCK position.

3. Move the throttle midway between the FAST and SLOW positions.

4. Move both motion-control levers forward until they both hit the stops in the T-slot.

5. Check which way the machine tracks.

6. If the machine tracks to the right, insert a 3/16 inch hex wrench through the access hole in the left, front cover panel and rotate the tracking screw clockwise or counterclockwise to adjust the travel of the lever (Figure 55).

7. If the machine tracks to the left, insert a 3/16 inch hex wrench through the access hole in the right, front cover panel and rotate the tracking screw clockwise or counterclockwise to adjust the travel of the lever (Figure 55).

8. Drive the machine and check the full forward tracking.

9. Repeat the adjustment until the desired tracking is obtained.

   

   Figure 55

   Right control lever shown

   1. Tracking screw
   2. Access hole on the front cover panel

Maintain the air pressure in the caster tires and rear tires at 90 kPa (13 psi). Uneven tire pressure can cause uneven cut. Check the tires when they are cold to get the most accurate pressure reading.

Figure 56

Check and torque the wheel lug nuts to 122 to 136 N∙m (90 to 100 ft-lb).

If you need to adjust the parking brake, contact an Authorized Service Dealer.

Replace the belt if it is worn. The signs of a worn belt include squealing while the belt is rotating; the blades slipping while cutting grass; and frayed edges, burn marks, and cracks on the belt.

1. Park the machine on a level surface, disengage the blade-control switch (PTO), and engage the parking brake.

2. Shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position.

3. Lower the mower to the 76 mm (3 inches) height of cut.

4. Loosen the bolt on each belt cover.

5. Release the mower-deck curtain by removing the cotter pin; refer to Releasing the Mower-Deck Curtain.

6. Remove the sheet-metal guard; refer to Removing the Sheet-Metal Guard.

7. Remove the belt covers (Figure 57).

   

   Figure 57

8. Use a 3/8-inch ratchet in the square hole in the idler arm to remove tension on the idler spring (Figure 58).

9. Remove the belt from the mower-deck pulleys and the clutch pulley.

10. Remove the belt guide on the spring-loaded idler arm (Figure 58).

11. Remove the existing belt.

12. Install the new belt around the mower pulleys and the clutch pulley under the engine (Figure 58).

    

    Figure 58

    1. Spring
    2. Clutch pulley
    3. Mower belt
    4. Spring-loaded idler assembly
    5. Ratchet
    6. Square hole in the idler arm for the ratchet

13. Install the belt guide on the idler arm (Figure 58).

14. Using the 3/8-inch ratchet in the square hole, install the idler spring (Figure 58).

    Note: Ensure that the spring ends are seated in the anchor grooves.

15. Install the belt covers (Figure 59).

    

    Figure 59

1. Park the machine on a level surface, disengage the blade-control switch (PTO), and engage the parking brake.

2. Shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position.

3. Remove the mower belt; refer to Replacing the Mower Belt.

4. Raise the machine and support it with jack stands.

5. Use a 1/2-inch ratchet or breaker bar in one of the square holes in the idler arm to remove tension on the idler spring (Figure 60).

6. Remove the existing belt from the idler pulley, 2 hydraulic-pump-drive pulleys, and engine pulley (Figure 60).

7. Install the new belt around the idler pulley, engine pulley, and 2 hydraulic-pump pulleys (Figure 60).

8. Using the 1/2-inch ratchet or breaker bar in one of the square holes, install the idler spring.

   Note: Ensure that the spring ends are seated in the anchor grooves.

9. Install the mower belt; refer to Replacing the Mower Belt.

   

   Figure 60

   1. Idler pulley
   2. Square hole in the idler arm for the ratchet
   3. Engine pulley
   4. Idler arm
   5. Hydraulic pump-drive belt
   6. Right hydraulic-pump pulley
   7. Mower belt
   8. Idler-spring post
   9. Left hydraulic-pump pulley

If the ends of the levers hit against each other, refer to Adjusting the Motion-Control Linkage.

Located on either side of the machine, below the seat, are the pump-control linkages. Rotating the end nut with a 1/2-inch deep socket wrench allows fine tuning adjustments so that the machine does not move in neutral. Any adjustments should be made for neutral positioning only.

1. Park the machine on a level surface, disengage the blade-control switch (PTO), and engage the parking brake.

2. Shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position.

3. Push the deck-lift pedal, remove the height-of-cut pin, and lower the mower deck to the ground

4. Raise the rear of the machine up and support it with jack stands (or equivalent support) just high enough to allow the drive wheels to turn freely.

5. Remove the electrical connection from the seat safety switch, located under the bottom cushion of the seat.

   Note: The switch is a part of the seat assembly.

6. Temporarily install a jumper wire across the terminals in the connector of the main wire harness.

7. Start the engine, run it at full throttle, and disengage the parking brake.

   Note: Before starting the engine, ensure that the parking brake is engaged and that the motion-control levers are out. You do not have to be in the seat.

8. Run the machine at least 5 minutes with the drive levers at full forward speed to bring the hydraulic fluid up to the operating temperature.

   Note: The motion-control levers must be in neutral while you are making any adjustments.

9. Bring the motion-control levers into the NEUTRAL position.

10. Check and ensure that the control-plate tabs touch the return-to-neutral plates on the hydraulic units.

11. Adjust the pump-control-rod lengths by rotating the nut in the appropriate direction until the wheels slightly creep in reverse (Figure 63 and Figure 64).

    

    Figure 63

    1. Access hole for 1/2-inch socket
    

    Figure 64

    1. Nut
    2. Stationary plate
    3. Control plate
    4. Return-to-neutral plate
    5. Tabs touching return to neutral plate

12. Move the motion-control levers to the REVERSE position and while applying slight pressure to the lever, allow the reverse-indicator springs to bring the levers back to neutral.

    Note: The wheels should stop turning or slightly creep in reverse.

    Note: You may need to remove the motion-control cover to gain access.

13. Shut off the machine.

14. Remove the jumper wire from the wire harness and plug the connector into the seat switch.

15. Remove the jack stands.

16. Raise the mower deck and install the height-of-cut pin.

17. Check and ensure that the machine does not creep in neutral with the parking brake disengaged.

Hydraulic Fluid Type: Toro^® HYPR-OIL^™ 500 hydraulic fluid

Important: Use the specified fluid. Other fluids could damage the hydraulic system.

Hydraulic System Capacity (with filters removed): 7.57 L (8 US qt)

1. Allow the hydraulic fluid to cool down. Check the oil level when the fluid is cold.

2. Check expansion reservoir and if necessary add Toro^® HYPR-OIL^™ 500 hydraulic fluid to the FULL COLD line (Figure 65).

   

   Figure 65

   1. Expansion tank
   2. Engine

To replace the hydraulic fluid, the filters need to be removed. Replace both at the same time; refer to Hydraulic-Fluid Specifications for fluid specifications.

Purge any air in the system after you install the new filters and add fluid. Refer to Bleeding the Hydraulic System. Repeat the bleeding process until the fluid remains at the FULL COLD line in the reservoir after purging.

Important: Failure to properly perform this procedure can result in irreparable damage to the transaxle drive system.

1. Raise the rear of machine and support it with jack stands (or equivalent support) just high enough to allow the drive wheels to turn freely.

   

   Figure 68

   1. Jacking points

2. Start the engine, move the throttle control ahead to the 1/2 throttle position, and disengage the parking brake.

   1. Move the bypass levers into the pushing the machine position. With the bypass valves open and the engine running, slowly move the motion-control levers in both forward and reverse 5 or 6 times.

   2. Move the bypass levers into the operating the machine position.

   3. With the bypass valve closed and the engine running, slowly move the control lever in both forward and reverse directions 5 to 6 times.

   4. Shut off the engine and check the fluid level in the expansion reservoir. Add the specified fluid until it reaches the FULL COLD line on the expansion reservoir.

3. Repeat step 2 until all the air is completely purged from the system.

   Note: When the transaxle operates at normal noise levels, moves smoothly forward, and reverses at normal speeds, it is purged.

4. Check the fluid level in the expansion reservoir a final time. Add the specified fluid as until it reaches the FULL COLD line on the expansion reservoir.

To ensure a superior quality of cut, keep the blades sharp. For convenient sharpening and replacement, you may want to keep extra blades on hand.

Check to ensure that the mower deck is level any time you install the mower or when you see an uneven cut on your lawn.

Check the mower deck for bent blades prior to leveling, and remove and replace any bent blades; refer to Servicing the Cutting Blades before continuing.

Level the mower deck side-to-side first; then you can adjust the front-to-rear slope.

Requirements:

• The machine must be on a level surface.

• All tires must be properly inflated; refer to Checking the Tire Pressure.

1. Park the machine on a level surface, disengage the blade-control switch (PTO), and engage the parking brake.

2. Shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position.

3. Check the tire pressure in the drive tires; refer to Checking the Tire Pressure.

4. Position the mower deck in the transport-lock position or the highest height-of-cut setting.

5. Carefully rotate the blades from side to side.

6. Measure between the blade tip and the flat surface (Figure 79). If both measurements are not within 5 mm (3/16 inch), adjust the leveling; continue with this procedure.

   

   Figure 79

   1. Blades side to side
   2. Blade tip
   3. Measure from the tip of the blade to the flat surface here.

7. Check the front-to-rear blade level (Figure 80). Ensure the front blade tip is lower than the rear blade tip as shown in the block height and rake table. If adjustment is needed, continue with this procedure.

   

   Figure 80

   1. Blades front to rear
   2. Blade tip
   3. Measure from the tip of the blade to the flat surface here.

8. Set the anti-scalp rollers to top holes or remove them completely for this adjustment.

9. Raise the deck to the transport position (140 mm or 5-1/2 inches).

10. Slowly loosen the adjusting screw on the lift-assist spring until you can remove the screw (Figure 81).

    Note: Save the screw for installation.

    

    Figure 81

    1. Adjusting screw
    2. Bracket
    3. Set the gap to 22 to 29 mm (7/8 to 1-1/8 inches).

11. Place 2 blocks (see Block Height and Rake Table) under the rear edge of the cutting deck skirt; 1 on each side of the cutting deck (Figure 82).

12. Set the height-of-cut lever to the 76 mm (3 inches) position; refer to Adjusting the Height of Cut.

13. Place 2 blocks under each side of the front edge of the deck, but not under the anti-scalp roller brackets or welds.

    

    Figure 82

    Bottom view

    1. Block—73 mm (2-7/8 inches)
    2. Welds

    Block Height and Rake Table

    Deck Size	Front Block Height	Rake
    All mower decks	73 mm (2-7/8 inches)	4.8 to 6.4 mm (3/16 to 1/4 inch)

14. Carefully rotate the blades side to side (Figure 79).

15. Lower the mower deck to the 76 mm (3 inches) position; refer to Adjusting the Height of Cut.

16. Loosen the locknuts (Figure 83) on all 4 corners and ensure that the mower deck is sitting securely on all 4 blocks.

17. Remove any slack from the deck hangers and make sure the deck-lift foot lever is pushed back against the stop.

18. Tighten the 4 locknuts.

    

    Figure 83

    1. Locknuts
    2. Deck lift arm
    3. Deck hanger
    4. Chain

19. Ensure that the blocks fit snugly under the deck skirt and that all attachment bolts are tight

20. Continue leveling the deck by checking the front-to-rear blade slope.

21. Check the blades for levelness and repeat deck leveling procedure if necessary.

22. Raise the deck to the transport position (140 mm or 5-1/2 inches).

23. Install the lift-assist spring adjusting screw previously removed in step 10.

24. Set the gap between the spring and the bracket to 22 to 29 mm (7/8 to 1-1/8 inches).

Before servicing or removing the mower deck, lock out the spring-loaded deck arms.

1. Park the machine on a level surface, disengage the blade-control switch (PTO), and engage the parking brake.

2. Shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position.

3. Lower the mower to the 76 mm (3 inches) height of cut.

4. Release the mower-deck curtain by removing the cotter pin; refer to Releasing the Mower-Deck Curtain.

5. Remove the belt covers.

6. Loosen the mower deck idler and remove the mower belt; refer to Belt Maintenance.

7. Remove the bolts and nuts from the front of the plate under the footrest.

8. Remove and retain the bolts and nuts on both sides of the machine (Figure 84).

   

   Figure 84

   1. Remove the nuts and bolts here.
   2. Remove the nuts and bolts here.

9. Slide the deck out to the right side of the machine.

1. Remove the locknut, bolt, spring, and spacer holding the deflector to the pivot brackets (Figure 85).

2. Remove the damaged or worn grass deflector (Figure 85).

   

   Figure 85

   1. Bolt
   2. Spacer
   3. Locknut
   4. Spring
   5. Spring installed
   6. Grass deflector
   7. J-hook end of spring

3. Place the spacer and the spring onto grass deflector.

4. Place 1 J-hook end of the spring behind the deck edge.

   Note: Make sure that 1 J-hook end of the spring is installed behind the deck edge before installing the bolt as shown in Figure 85.

5. Install the bolt and the nut.

6. Place 1 J-hook end of the spring around the grass deflector (Figure 85).

   Important: The grass deflector must be able to rotate. Lift the deflector up to the full open position and ensure that it rotates into the full down position.

1. Park the machine on a level surface, disengage the blade-control switch (PTO), and engage the parking brake.

2. Shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position.

3. Raise the mower deck to the TRANSPORT position.

Use compressed air to clean the suspension system.

Note: Do not clean the shock assemblies with pressurized water (Figure 86).

Figure 86

Engine oil, batteries, hydraulic fluid, and engine coolant are pollutants to the environment. Dispose of these according to your state and local regulations.