Interactive Manual

Introduction

Read this information carefully to learn how to operate and maintain your product properly and to avoid injury and product damage. You are responsible for operating the product properly and safely.

Visit www.Toro.com for product safety and operation training materials, accessory information, help finding a dealer, or to register your product.

Whenever you need service, genuine Toro parts, or additional information, contact an Authorized Service Dealer or Toro Customer Service and have the model and serial numbers of your product ready. Figure 1 identifies the location of the model and serial numbers on the product. Write the numbers in the space provided.

Figure 1

Model and serial number location

This manual identifies potential hazards and has safety messages identified by the safety-alert symbol (Figure 2), which signals a hazard that may cause serious injury or death if you do not follow the recommended precautions.

Figure 2

Safety-alert symbol

This manual uses 2 words to highlight information. Important calls attention to special mechanical information and Note emphasizes general information worthy of special attention.

Warning

CALIFORNIA

Proposition 65 Warning

Use of this product may cause exposure to chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm.

Safety

Warning

When the bagger is in operation, the blower is rotating and can cut off or injure hands and fingers.

Before adjusting, cleaning, repairing, and inspecting the blower, and before unclogging the chute, shut off the engine and wait for all moving parts to stop. Remove the key.
Use a stick, not your hands, to remove an obstruction from the blower and tube.
Keep hands and feet away from moving parts. Do not make adjustments with the engine running.

Warning

Debris, such as leaves, grass, or brush can catch fire. A fire in the engine area can cause personal injury and property damage.

Keep the engine and muffler area free of debris accumulation.
Take care when opening the bagger cover to keep debris from falling onto the engine and muffler area.
Allow the machine to cool before storing it.

The following list contains safety information specific to Toro products and other safety information you must know.

Become familiar with the safe operation of the equipment, with the operator controls, and safety signs.
Use extra care with grass catchers or other attachments. These can change the operating characteristics and the stability of the machine.
Follow the recommendations for adding or removing weights as described in the Operator’s Manual for the machine.
Do not use a grass catcher on steep slopes. A heavy grass catcher could cause loss of control or overturn the machine.
Slow down and use extra care on hillsides. Mow slopes side to side. Turf conditions can affect the stability of the machine. Use extreme caution while operating near drop-offs.
Keep all movement on slopes slow and gradual. Do not make sudden changes in speed, directions, or turning.
The grass catcher can obstruct the view to the rear. Use extra care when operating the machine in reverse.
Use care when loading or unloading the machine into a truck or trailer.
Do not use the mower deck without the discharge deflector or grass catcher.
Park the machine on a level surface, disengage the drives, engage the parking brake, and shut off the engine before leaving the operator's position for any reason including unclogging or emptying the grass catcher.
If you remove the grass catcher, install any discharge deflector or guard that was removed to install the grass catcher. Do not operate the machine without either the entire grass catcher or the grass deflector in place.
Do not leave grass in the grass catcher for extended periods of time.
Grass catcher components are subject to wear, damage, and deterioration, which could expose moving parts or allow objects to be thrown. Frequently check components and replace them with manufacturer's recommended parts when necessary.

Towing Safety

Do not attach towed equipment except at the hitch point.
Follow the attachment manufacturer's recommendation for weight limits for towed equipment and towing on slopes.
Never allow children or others in or on towed equipment.
On slopes, the weight of the towed equipment may cause loss of traction and loss of control. Reduce towed weight and slow down.
Stopping distance increases with the weight of the towed load. Travel slowly and allow extra distance to stop.
Make wide turns to keep the attachment clear of the machine.
Do not tow a load that weighs more than the towing machine.

Safety and Instructional Decals

Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing.

136-4164

Warning—read the Operator’s Manual.
Warning—hearing protection must be worn.
Thrown object hazard—do not operate the blower without the entire system installed and latched.
Cutting/dismemberment hazard, impeller—keep away from moving parts; keep all guards and covers in place.
Cutting/dismemberment hazard, impeller—disengage the PTO, remove the key, and wait for all moving parts to stop.
Warning; loss of traction—do not operate with only counterbalance weights installed; do not operate with only E-Z Vac installed; operate only with both E-Z Vac and counterbalance weights installed.

109-6809

Crushing hazard of hand—Do not remove the whole bagger from the machine. Step 1: Open the bagger top. Step 2: Remove the bag(s) from the bagger. Step 3: Do not remove the bagger top when it is closed; open the bagger top and then remove it.

133-8061

Setup

Determine the left and right sides of the machine from the normal operating position.

Preparing the Machine

Perform the following procedure to prepare the machine for attaching the blower and finishing kit.

Park the machine on a level surface.
Disengage the blade-control switch, engage the parking brake, and move the motion-control levers outward to the NEUTRAL-LOCK position.
Shut off the engine and remove the key.
Ensure that the machine is secure from movement before you begin to work on it.
Repair all bent or damaged areas of machine deck and replace any missing parts.
Clean the machine of any debris on the machine deck or rear part of the machine to ease installation.

Installing the Weight

Parts needed for this procedure:

Weight tray	1
Left weight-tray mount	1
Right weight-tray mount	1
Suitcase weight—16 kg (35 lb)	1
Retaining rod	1
Bolt (3/8 x 1-1/4 inches)	2
Flange nut (3/8 inch)	4
Carriage bolt (3/8 x 1 inch)	2
Self-tapping bolt (5/16 x 3/4 inch)	2

Caution

The bagger changes the weight distribution of the machine. Operating the machine without the front weights may cause an unstable condition, which could result in a loss of control.

Ensure the front weights are properly installed before operating the machine with the bagger attachment.

Remove the existing bolt and nut from the left and right side of the platform where you will install the weight-tray mounts.
Use the 2 self-tapping bolts (5/16 x 3/4 inch), 2 bolts (3/8 x 1-1/4 inches), and flange nuts (3/8 inch) to secure the left and right weight-tray mounts to the machine (Figure 3).
Figure 3

Cutaway view
1. Weight-tray mounts
2. Bolt (3/8 x 1-1/4 inches)
3. Flange nut (3/8 inch)
4. Self-tapping bolt (5/16 x 3/4 inch)
Use the 2 carriage bolts (3/8 x 1 inch) and flange nuts to secure the weight tray to the mounts (Figure 4).
Figure 4
1. Carriage bolt (3/8 x 1 inch)
2. Weight-tray mount
3. Weight tray
4. Flange nut (3/8 inch)
Insert the suitcase weight into the weight tray with the groove side facing toward the front of the machine (Figure 5).
Figure 5
1. Retaining rod
2. Weight tray
3. Suitcase weight
Insert the retaining rod into the tray and rotate it into the locked position (Figure 5).

Important: Remove the suitcase weight whenever you remove the bagger attachment.

Removing the Grass Deflector and Belt Cover

Warning

An uncovered discharge opening could allow the lawn mower to throw objects in the operator’s or bystander’s direction and result in serious injury. Also, contact with the blade could occur.

Never operate the lawn mower unless you install a mulch plate, discharge deflector, or grass-collection system.

Inspect the grass deflector for damage before each use. Replace any damaged parts before use.

Disengage the spring from the notch in the deflector bracket and remove the cotter pin (CE models only), slide the rod out of the welded deck brackets, spring, and discharge deflector (Figure 6).
Figure 6
1. Rod
2. Cotter pin (CE models only)
3. Deflector
4. Spring
5. Deck brackets
6. Spring installed over the rod
Remove the deflector (Figure 6).
Remove the 4 screws (1/4 x 1/2 inch) securing the right belt cover, and remove the belt cover (Figure 7).

Note: Retain the 4 screws (1/4 x 1/2 inch) for installation in Procedure Installing the Pulley Assembly, Belt Cover, and Shoulder Bolt.
Figure 7
1. Screw (1/4 x 1/2 inch)
2. Belt cover

Installing the Baffle and Blower Support

Parts needed for this procedure:

Blower support	1
Hex washer-head screw (3/8 x 3/4 inch)	2
Baffle	1
Carriage bolt (5/16 x 3/4 inch)	4
Flange nut (5/16 inch)	4

Install the blower support to the mower deck using 2 hex washer-head screws (3/8 x 3/4 inch) as shown in Figure 8.
Figure 8
1. Hex washer-head screw (3/8 x 3/4 inch)
2. Blower support
Remove the existing bolt and nut from the mower deck (Figure 9).

Important: For 48-inch and 60-inch mower decks, there is only one bolt and nut that you can remove.For 54-inch mower deck, remove the bolt and nut as shown in Figure 9.
Figure 9
1. Existing bolt
2. Existing nut
Install the left side of the baffle using a carriage bolt (5/16 x 3/4 inch) and flange nut (5/16 inch) as shown in Figure 10.
Loosen the 2 carriage bolts (5/16 x 3/4 inch) in the baffle slots, and slide the baffle until the hole aligns with the hole in the mower deck (Figure 10).
Install baffle as shown in Figure 10.

Important: Ensure that you use the correct hole for the baffle; refer to Figure 10.
Tighten the 2 carriage bolts (5/16 x 3/4 inch) in the baffle slots (Figure 10).
Figure 10

54-inch mower deck shown
1. Inner baffle
2. Hole for 48-inch and 60-inch mower deck installation.
3. Hole for 54-inch mower deck installation.
4. Right blade
5. Outer baffle
6. Install this carriage bolt (5/16 x 3/4 inch) and flange nut (5/16 inch) after sliding the baffle.
7. Slots in the baffle
8. Loosen these 2 carriage bolts (5/16 x 3/4 inch) and 2 flange nut (5/16 inch).
9. Install this carriage bolt (5/16 x 3/4 inch) and flange nut (5/16 inch) first.

Installing the Pulley Assembly, Belt Cover, and Shoulder Bolt

Parts needed for this procedure:

Pulley assembly	1
Belt cover	1

Remove the nut and washer from the right mower deck pulley.
Install the pulley assembly to the right mower deck pulley with the previously removed nut and washer (Figure 11).

Important: For 48-inch mower decks, use the small blower pulley.For 54-inch and 60-inch mower decks, use the large blower pulley.
Torque the nut to 136 to 149 N∙m (100 to 110 ft-lb).
Figure 11

54-inch mower deck shown
1. Existing pulley nut
2. Existing washer
3. Blower pulley
4. Existing deck (spindle) pulley
5. Spindle
Install the new belt cover over the pulley assembly using the 4 previously removed screws (1/4 x 1/2 inch) as shown in Figure 12.
Figure 12
1. Belt cover
2. Screw (1/4 x 1/2 inch)

Installing the Attachment Mount

Parts needed for this procedure:

Stabilizer bracket	1
Carriage bolt (5/16 x 3/4 inch)	2
Locknut (5/16 inch)	4
Self-tapping screw (5/16 x 3/4 inch)	2
Bolt (5/16 x 1 inch)	2
Pivot frame	1
Hairpin cotter	2
Rod	2
Washer	2

Remove the existing 2 bolts, 2 nuts, and hitch bracket from the bottom of the engine guard (Figure 13).
Figure 13
1. Nut
2. Existing hitch bracket
3. Bolt
Install the stabilizer bracket to the engine guard using 2 carriage bolts (5/16 x 3/4 inch) and 2 locknuts (5/16 inch) as shown in Figure 14.
Figure 14
1. Stabilizer bracket
2. Carriage bolt (5/16 x 3/4 inch)
3. Locknut (5/16 inch)
Remove the existing 2 self-tapping screws from the bottom of the machine frame (Figure 16).
Loosely install the pivot frame to the machine frame using 2 bolts (5/16 x 1 inch) and 2 locknuts (5/16 inch) as shown in Figure 15.
Figure 15
1. Machine frame
2. Locknut (5/16 inch)
3. Hole
4. Bolt (5/16 x 1 inch)
5. Pivot frame
Position the pivot frame upward, and secure the pivot frame to the bottom of the machine frame using 2 self-tapping screws (5/16 x 3/4 inch) as shown in Figure 16.
Figure 16
1. Self-tapping screw (5/16 x 3/4 inch)
2. Pivot frame
Tighten the 2 bolts (5/16 x 1 inch) and 2 locknuts (5/16 inch) as shown in Figure 15.
Install the bent, flared end of a rod into the keyed slot in the left side of the machine frame, and move the rod rearward to seat it in the frame (Figure 17).

Note: Repeat this step for the right side of the machine.
Figure 17

Left side shown
1. Pivot frame hole
2. Washer
3. Hairpin cotter
4. Support rod
5. Keyed slot (existing)
6. Bent, flared end of the rod
Insert the bent ends of the rods into the attachment mount as shown in Figure 17 and secure the end of each rod with a washer and hairpin cotter.

Installing the Latch Rod

Parts needed for this procedure:

Latch rod	1
Hairpin cotter	1

Install the latch rod with a hairpin cotter (Figure 18).

Figure 18

Hairpin cotter
Latch rod

Assembling the Bagger Top

Parts needed for this procedure:

Bagger top	1
Bagger screen	1
Hairpin cotter	2

Turn the bagger top over.
Install the screen as shown in Figure 19 and ensure that it slopes down toward the collection bags.

Note: Make sure that the screens snap into place and the tabs engage the bagger top.
Figure 19
1. Bagger top
2. Screen
3. Screen tab
4. Slot in bagger top
5. Hairpin cotter

Installing the Bagger Top

Parts needed for this procedure:

Grass Bag	2
Circular cotter pin	1

Install the bagger top to the bagger frame.
Slide the brackets over the posts in the bagger frame and install the circular cotter pin into the hole in the right hand post (Figure 20).
Rotate the bagger hood down to the operating position.

Note: To remove the circular cotter pin, continue to rotate it in the same direction as installed.
Figure 20
1. Bagger hood
2. Bagger frame
3. Bracket, bagger hood
4. Circular cotter pin
5. Post
Lift the bagger top and install the bags by sliding the bag frame hooks onto the retaining brackets (Figure 21).
Figure 21
1. Bag
2. Bagger frame
3. Retaining bracket
4. Bag frame hook
Lower the bagger top onto the bags (Figure 22).

Figure 22
Secure the hood with the latch (Figure 22).

Installing the Blower Assembly

Parts needed for this procedure:

Blower assembly

Warning

An uncovered discharge opening allows the lawn mower to throw objects toward you or bystanders, resulting in serious injury. Also, contact with the blade could occur.

Never operate the lawn mower without a cover plate, a mulch plate, or a grass chute and catcher.
Make sure that the grass deflector is installed when you remove the grass chute and catcher.

Important: Install the side-discharge chute when you remove the bagger and blower.

Important: Save all the hardware and the side-discharge chute.

If necessary, install the belt onto the blower pulley (Figure 25).
Insert the blower pivot pin into the blower support and rotate the blower assembly inward toward the machine (Figure 23).

Note: The blower assembly should automatically latch as shown in Figure 24.
Figure 23
1. Blower assembly
2. Blower pivot pin
3. Blower support
Figure 24
1. Blower latch

Installing the Blower Belt and Powered Bagger Cover

Parts needed for this procedure:

Powered bagger cover	1
Blower belt	1

Install the belt around the blower pulley (Figure 25 and Figure 26); refer to Installing the Blower Assembly.

Use the following belt based on the mower deck size:

48-inch Mower Deck 54-inch Mower Deck 60-inch Mower Deck

Toro Part No. 127-0074 Toro Part No. 127-0075 Toro Part No. 127-0076
Figure 25

Blower Belt Routing
1. Idler/tension pulley
2. Blower pulley
3. Blower belt
4. Drive pulley
Figure 26
1. Blower pulley
2. Blower in position (housing portion removed for illustrative purposes)
3. Spring
4. Idler-pulley post
5. Idler arm
6. Drive pulley
7. Idler/tension pulley
8. Blower belt
Ensure that the belt remains aligned to the blower pulley while you are installing the blower assembly.
Pull the spring loaded idler pulley away from the fixed spring post, and route the belt around the mower deck pulley (Figure 26).

Note: Ensure that the belt is routed around the blower pulley correctly.
Route the belt around the drive pulley as illustrated in Figure 25 and Figure 26.
Install the powered bagger cover over the belt cover, and secure it by tightening the knob (Figure 27).
Figure 27
1. Knob
2. Powered bagger cover
3. Belt cover

Installing the Discharge Tubes

Parts needed for this procedure:

Upper tube	1
Screw (1/4 x 3/4 inches)	2
Washer (1/4 inch)	2
Locknut (1/4 inch)	2
Lower tube	1

Important: Make sure that the mower deck is in the lowest height-of-cut position before installing the discharge tubes.

Note: Remember to install the grass deflector when you remove the bagger from the mower.

Disengage the PTO and engage the parking brake.
Shut off the engine and remove the key.
Lower the mower deck to the lowest height-of-cut position.
Remove the bags for viewing the tube under the hood.
Lower and latch the hood.
Use both latches to attach the lower tube to the blower assembly (Figure 28).

Note: Ensure the notch in the lower tube is at the bottom when installed (Figure 30).
Figure 28

Lower Discharge Tube Latch
1. Blower assembly
2. Upper latch
3. Latch
Make note of where the 2 bolts in the upper tube are installed.

Note: The hole near the molded arrowheads will not be used.
Remove the 2 bolts in the lower end of the upper tube.
Use the 2 holes as a template for the lower tube.

Note: Retain the hardware.
Insert the upper end (no holes) of the upper tube through the tube seal in the hood by pushing the tube in until the tube contacts the inside of the hood.
Pull the upper tube out slightly so that the seal extends outward and over the lower tube (Figure 29).
Figure 29
1. Upper tube
2. Rubber seal protruding out
3. Bagger hood
Align the upper tube holes to match the dimples on the surface of the lower tube.

Note: Ensure that the side profile appears as shown in Figure 30.

Note: Do not use the open hole near the molded arrowheads.
Figure 30
1. Upper tube
2. Existing hole (bolt removed)
3. Notch at the bottom of the tube when installed
4. Lower tube
Using the existing holes in the upper tube as a template, drill 2 holes, 6.5 mm (1/4 inch) diameter, through the dimples on the lower tube (Figure 31).
Figure 31

Drilling Lower Discharge Tube
1. Dimples
2. Lower tube
3. Drill 6.5 mm (1/4 inch) diameter hole
4. Upper tube
5. Install screw (1/4 x 3/4 inch), washer (1/4 inch), and locknut (1/4 inch) here.
6. Upper tube—existing holes
Remove the upper and lower tubes from the machine.
Slide the tubes together and align the holes.
Install the washers (1/4 inch) onto the bolts (Figure 31).
Using a hex key tool, install the screws (1/4 x 3/4 inch) and washers (1/4 inch) from the inside of the lower tube and through the existing holes in the upper tube (Figure 31).
Secure the tubes together with the nuts (1/4 inch) as shown in Figure 31.
Insert the upper discharge tube through the tube seal in the hood.
Pull the upper tube out slightly so that the seal extends outward and over the blower assembly (Figure 29).
Use both latches to attach the lower tube to the blower assembly (Figure 28).

Operation

Note: Determine the left and right sides of the machine from the normal operating position.

Warning

To avoid personal injury, follow these procedures:

Become familiar with all operating and safety instructions in the Operator's Manual for the mower before using this attachment.
Never remove the discharge tube, bags, bagger hood, or the chute while the engine is running.
Always shut the engine off and wait for all moving parts to stop before clearing an obstruction from the bagging system.
Never perform maintenance or repairs while the engine is running.

Emptying the Grass Bags

Be careful when lifting or handling a grass bag that is full. To empty the grass bags:

Park the machine on a level surface.
Disengage the blade-control switch, engage the parking brake, and move the motion-control levers outward to the NEUTRAL-LOCK position.
Shut off the engine and remove the key.
Raise the bagger hood (Figure 32).

Figure 32
Compress the debris into the bags.
With both hands, lift up on the bag and unhook it from the retaining bracket, empty the bag.
Repeat the procedure for the other bag.
Install the bags by sliding the bag frame hooks onto the retaining brackets (Figure 33).
Figure 33
1. Bag
2. Bagger frame
3. Retaining bracket
4. Bag frame hook
Lower the bagger hood onto the bags.

Clearing Obstructions from the Bagger System

Warning

When the bagger is in operation, the blower is rotating and can cut off or injure hands and fingers.

Before adjusting, cleaning, repairing and inspecting the blower, and before unclogging the chute, turn off the engine and wait for all moving parts to stop. Remove the key.
Use a stick, not your hands, to remove an obstruction from the blower and tube.
Keep your face, hands, feet, and any other part of your body or clothing away from concealed, moving, or rotating parts.

Park the machine on a level surface.
Disengage the blade-control switch, engage the parking brake, and move the motion-control levers outward to the NEUTRAL-LOCK position.
Shut off the engine and remove the key.
Empty the bags.
Unlatch the lower tube.
Remove the tubes from the bagger.
Use a stick or similar object, not your hands, to remove and clear the obstruction from the tube assembly.

Note: In most cases, you can shake the debris out of the tubes.
If the blower assembly is plugged, remove the plastic belt cover, unlatch the bagger blower assembly, remove the belt, and swing it open.
Use a stick or similar object, not your hands, to remove and clear the obstruction from the blower assembly.
After you remove the obstruction, install the complete bagger system and resume operation.

Removing the Bagger

Warning

Components around the engine will be hot if the machine has been running. Touching hot components can cause burns.

Do not touch engine components when hot.
Allow engine to cool before removing the bagger.

Caution

Failing to remove the front bagger weights and operating the machine without the bagger attachment may cause an unstable condition which could result in a loss of control.

Always remove the front weights when removing the bagger attachment.

Remove the bagger by repeating the setup sections from the Installation Instructions and Operator’s Manual in reverse order. Always remove the front baffles and front weights when removing the bagger attachments.

Important: Install the side-discharge chute when you remove the bagger and blower.

Note: It is only necessary to remove the cutoff baffle when installing a mulching kit.

Operating Tips

Tips for Bagging

Remembering the Size of the Machine with the Attachment

Remember that the machine is longer and wider with this attachment installed. By turning too sharply in confined places you may damage the attachment.

Trimming

Always trim with the left side of the mower. Do not trim with the right side of the mower because you could damage the bagger chute and discharge tube.

Cutting Height

Do not set the mower cutting height too low because long grass surrounding the mower can prevent air from getting under the mower and entering the bagging system. If enough air does not get under the mower, the bagging system will plug.

Cutting Frequency

Cut the grass often, especially when it grows rapidly. You will need to cut your grass twice if it gets excessively long.

Cutting Technique

For best lawn appearance, be sure to slightly overlap the mower into the previously cut area. This helps reduce the load on the engine and reduces the chance of plugging the chute and discharge tube.

Bagging Speed

Most often you will bag with the mower throttle in the FAST position and drive at a normal ground speed. However, in extremely dry and dusty grass, you may want to slightly reduce the throttle speed and increase the ground speed of the mower. The bagging system may plug if you drive too fast and the engine speed gets too slow. On hills, it may be necessary to slow the mower ground speed. This helps maintain the engine speed and bagging efficiency. Mow downhill whenever possible.

Caution

As the bagger fills, extra weight is added to the back of the machine. If you stop and start suddenly on hills, you may lose steering control or the machine may tip.

Do not start or stop suddenly when going uphill or downhill. Avoid uphill starts.
If you do stop the machine when going uphill, disengage the blade control. Then back down the hill using a slow speed.
Avoid sudden turns or rapid speed changes on slopes.
Never operate the machine without the bagger attachment and the front weights still installed.

Bagging Long Grass

Excessively long grass is heavy and may not be propelled completely into the grass bags. If this happens, the discharge tube and chute may plug. To avoid plugging the bagging system, mow the grass at a high height of cut, then lower the mower to your normal cutting height and repeat the bagging process.

Bagging Wet Grass

Always try to cut grass when it is dry because your lawn will have a neat appearance. If you must cut wet grass, use the conventional side discharge feature of the mower. Several hours later, when the clippings are dry, install the complete bagger attachment and vacuum up the grass clippings.

Signs of Plugging

As you are bagging, a small amount of grass clippings normally blow out the front of the mower. An excessive amount of clippings blowing out indicates that the bags are full or the system is plugged.

Maintenance

Note: Determine the left and right sides of the machine from the normal operating position.

Recommended Maintenance Schedule(s)

Maintenance Service Interval	Maintenance Procedure
After the first 8 hours	Inspect the blower belt. Inspect the bagger.
After each use	Clean the hood screen. Clean the bagger.
Every 25 hours	Inspect the blower belt.
Every 100 hours	Inspect the bagger.

Warning

If you leave the key in the key switch, someone could accidently start the engine and seriously injure you or other bystanders.

Remove the key and disconnect the wire from the spark plug before you do any maintenance. Set the wire aside so that it does not accidentally contact the spark plug.

Warning

Engines can become hot when they are operating. Severe burns can occur from contacting hot surfaces.

Allow engines, especially the muffler, to cool before touching.

Warning

Debris, such as leaves, grass, or brush can catch fire. A fire in the engine area can cause personal injury and property damage.

Keep the engine and muffler area free of debris accumulation.
Take care when opening the bagger cover to keep debris from falling onto the engine and muffler area.
Allow the machine to cool before storing it.

Preparing for Maintenance

Do the following steps before preforming maintenance on the machine:

Park the machine on a level surface.
Disengage the PTO, move the motion control levers to the NEUTRAL-LOCK position, and engage the parking brake.
Shut off the engine and remove the key.
Clean the mower of any debris on the deck or rear part of the mower to ease maintenance.

Cleaning the Hood Screen

Maintenance Service Interval	Maintenance Procedure
After each use	Clean the hood screen.

Open the bagger hood.
Clean the debris from the screen.
Close the bagger hood.

Cleaning the Bagger and Bags

Maintenance Service Interval	Maintenance Procedure
After each use	Clean the bagger.

Wash the inside and outside of the bagger hood, bags, tube, and the underside of the mower.

Note: Use a mild automotive detergent to remove dirt.
Make sure that you remove matted grass from all parts.
After washing all parts, let them dry thoroughly.

Note: With all parts installed, start and run the machine for a minute to assist in drying.

Inspecting the Blower Belt

Maintenance Service Interval	Maintenance Procedure
After the first 8 hours	Inspect the blower belt.
Every 25 hours	Inspect the blower belt.

Check belts for cracks, frayed edges, burn marks or any other damage. Replace damaged belts.

Replacing the Blower Belt

Remove the plastic belt cover.
Pull back on the spring-loaded idler pulley to relieve the belt tension (Figure 34).
Figure 34
1. Blower pulley
2. Blower in position (housing portion removed for illustrative purposes)
3. Drive pulley
4. Mower deck
5. Idler/tension pulley
6. Blower belt
Remove the existing bagger belt from the mower-deck pulley.
Remove the blower from the mower deck.
Remove the existing bagger belt from the blower pulleys.
Install the new belt around the blower pulleys (Figure 34).
Install the blower onto the blower support.
Install the new belt around the mower-deck pulley (Figure 34).
Pull back on the spring loaded idler pulley and install the belt onto the spring-loaded idler pulley (Figure 34).

Inspecting the Bagger

Maintenance Service Interval	Maintenance Procedure
After the first 8 hours	Inspect the bagger.
Every 100 hours	Inspect the bagger.

Check the upper tube, lower tube, bagger hood, and the blower assembly.

Note: Replace these parts if they are cracked or broken.
Check the bags, bagger frame, and screen.

Note: Replace any parts that are cracked or broken.
Tighten all nuts bolts and screws.

Inspecting the Mower Blades

Inspect the mower blades regularly and whenever a blade strikes a foreign object.
If blades are badly worn or damaged, install new blades; refer to your machine Operator's Manual for complete blade maintenance.

Storage

Storing the Bagger Attachment

Clean the bagger attachment; refer to Cleaning the Bagger Attachment.
Inspect the bagger attachment for damage; refer to Inspecting the Bagger Attachment.
Ensure that the grass bags are empty and thoroughly dry.
Store the bagger in a clean, dry place, out of direct sunlight. This protects the plastic parts and extends the life of the bagger. If you must store the bagger outside, cover it with a weatherproof cover.

Troubleshooting

Problem	Possible Cause	Corrective Action
There is abnormal vibration.	The cutting blade(s) are bent or unbalanced. The blade-mounting bolt is loose. There is a loose blower pulley or pulley assembly. The bagger belt is worn. The blower fan blade(s) are bent or unbalanced.	Install new cutting blade(s). Tighten the blade-mounting bolt. Tighten the appropriate pulley. Replace the belt. Contact an Authorized Service Dealer.
Reduced bagging performance	The engine speed is too low. The screen in the bagger hood is plugged. The bagger belt is loose. There is a plugged tube or blower. The bags are full.	Always operate the engine at full throttle. Remove debris, leaves, or grass clippings from the screen. Replace the bagger belt. Locate and remove the plugged debris. Empty the hopper.
The blower and tubes plug too frequently.	The bags are too full. The engine speed is too low. The grass is too wet. The grass is too long. The screen in the bagger hood is plugged. The ground speed is too fast. The bagger belt is worn.	Dump more frequently. Always operate the engine at full throttle. Cut grass when it is dry. Cut no more than 51 to 76 mm (2 to 3 inches) or 1/3 of the grass height, whichever is less. Remove debris, leaves, or grass clippings from the screen. Drive slower at full throttle. Replace the belt.
Debris blowout	The bags are too full. The ground speed is too fast. The mower deck is not leveled.	Dump more frequently. Drive the machine at slow ground speed while operating the engine at full throttle. See the machine Operator's Manual for leveling the mower deck.
The blower impeller does not spin freely.	The blower is plugged. The impeller is not aligned.	Remove debris, leaves, or grass clippings from the blower impeller. Contact an Authorized Service Dealer.

48-inch Mower Deck	54-inch Mower Deck	60-inch Mower Deck
Toro Part No. 127-0074	Toro Part No. 127-0075	Toro Part No. 127-0076

E-Z Vac™ Complete Twin Bagger

TimeCutter® HD Riding Mower

Model No. 79345-Serial No. 400000000 and Up

Introduction

Warning

Safety

Warning

Warning

Towing Safety

Safety and Instructional Decals

Setup

Preparing the Machine

Installing the Weight

Caution

Removing the Grass Deflector and Belt Cover

Warning

Installing the Baffle and Blower Support

Installing the Pulley Assembly, Belt Cover, and Shoulder Bolt

Installing the Attachment Mount

Installing the Latch Rod

Assembling the Bagger Top

Installing the Bagger Top

Installing the Blower Assembly

Warning

Installing the Blower Belt and Powered Bagger Cover

Installing the Discharge Tubes

Operation

Warning

Emptying the Grass Bags

Clearing Obstructions from the Bagger System

Warning

Removing the Bagger

Warning

Caution

Operating Tips

Tips for Bagging

Remembering the Size of the Machine with the Attachment

Trimming

Cutting Height

Cutting Frequency

Cutting Technique

Bagging Speed

Caution

Bagging Long Grass

Bagging Wet Grass

Signs of Plugging

Maintenance

Recommended Maintenance Schedule(s)

Warning

Warning

Warning

Preparing for Maintenance

Cleaning the Hood Screen

Cleaning the Bagger and Bags

Inspecting the Blower Belt

Replacing the Blower Belt

Inspecting the Bagger

Inspecting the Mower Blades

Storage

Storing the Bagger Attachment

Troubleshooting