Maintenance Service Interval | Maintenance Procedure |
---|---|
Before each use or daily |
|
This rotary-blade, walk-behind lawn mower is intended to be used by residential homeowners. It is designed primarily for cutting grass on well-maintained lawns on residential properties. Using this product for purposes other than its intended use could prove dangerous to you and bystanders.
Read this information carefully to learn how to operate and maintain your product properly and to avoid injury and product damage. You are responsible for operating the product properly and safely.
Visit www.Toro.com for more information, including safety tips, training materials, accessory information, help finding a dealer, or to register your product.
Whenever you need service, genuine Toro parts, or additional information, contact an Authorized Service Dealer or Toro Customer Service and have the model and serial numbers of your product ready. Figure 1 identifies the location of the model and serial numbers on the product. Write the product model and serial numbers in the space provided.
Important: With your mobile device, you can scan the QR code on the serial number decal (if equipped) to access warranty, parts, and other product information.
The safety-alert symbol (Figure 2) shown in this manual and on the machine identifies important safety messages that you must follow to prevent accidents.
The safety-alert symbol appears above information that alerts you to unsafe actions or situations and is followed by the word DANGER, WARNING, or CAUTION.
DANGER indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
WARNING indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
This manual uses two other words to highlight information. Important calls attention to special mechanical information and Note emphasizes general information worthy of special attention.
It is a violation of California Public Resource Code Section 4442 or 4443 to use or operate the engine on any forest-covered, brush-covered, or grass-covered land unless the engine is equipped with a spark arrester, as defined in Section 4442, maintained in effective working order or the engine is constructed, equipped, and maintained for the prevention of fire.
The enclosed engine owner's manual is supplied for information regarding the US Environmental Protection Agency (EPA) and the California Emission Control Regulation of emission systems, maintenance, and warranty. Replacements may be ordered through the engine manufacturer.
Gross or Net Torque: The gross or net torque of this engine was laboratory rated by the engine manufacturer in accordance with the Society of Automotive Engineers (SAE) J1940 or J2723. As configured to meet safety, emission, and operating requirements, the actual engine torque on this class of mower will be significantly lower. Please refer to the engine manufacturer’s information included with the machine.
CALIFORNIA
Proposition 65 Warning
The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm.
Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and reproductive harm. Wash hands after handling.
Use of this product may cause exposure to chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm.
This product is capable of amputating hands and feet and of throwing objects. Always follow all safety instructions to avoid serious personal injury or death.
Read, understand, and follow the instructions and warnings in this Operator’s Manual and on the machine and attachments before starting the engine.
Do not put your hands or feet near moving parts or under the machine. Keep clear of any discharge opening.
Do not operate the machine without all guards and other safety protective devices in place and functioning properly on the machine.
Keep bystanders and children out of the operating area. Do not allow children to operate the machine. Allow only people who are responsible, trained, familiar with the instructions, and physically capable to operate the machine.
Stop the machine, shut off the engine, remove the ignition key (if equipped), and wait for all moving parts to stop before servicing, fueling, or unclogging the machine.
Improperly using or maintaining this machine can result in injury.
To reduce the potential for injury, comply with these safety instructions
and always pay attention to the safety-alert symbol , which means Caution, Warning,
or Danger—personal safety instruction. Failure to comply with
these instructions may result in personal injury or death.
![]() |
Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. |
Electric-start model only
Electric-start model only
Electric-start model only
Important: Remove and discard the protective plastic sheet that covers the engine and any other plastic or wrapping on the machine.
Important: To prevent accidental starting, do not insert the key into the electric-start ignition (if equipped) until you are ready to start the engine.
Assembling and unfolding the handle improperly can damage the cables, causing an unsafe operating condition.
Do not damage the cables when unfolding the handle.
If a cable is damaged, contact an Authorized Service Dealer.
Important: If the oil level in the engine is too low or too high and you run the engine, you may damage the engine.
Electric-Start Model Only
Refer to Charging the Battery.
Model | Weight | Length | Width | Height |
21219 | 65 kg | 169 cm | 81 cm | 118 cm |
(143 lb) | ||||
21220 | 67 kg | (67 inches) | (32 inches) | (47 inches) |
(148 lb) |
A selection of Toro approved attachments and accessories is available for use with the machine to enhance and expand its capabilities. Contact your Authorized Service Dealer or authorized Toro distributor or go to www.Toro.com for a list of all approved attachments and accessories.
To ensure optimum performance and continued safety certification of the machine, use only genuine Toro replacement parts and accessories. Replacement parts and accessories made by other manufacturers could be dangerous, and such use could void the product warranty.
Note: Determine the left and right sides of the machine from the normal operating position.
Always shut off the machine, remove the ignition key (if equipped), wait for all moving parts to stop, and allow the machine to cool before adjusting, servicing, cleaning, or storing it.
Become familiar with the safe operation of the equipment, operator controls, and safety signs.
Check that all guards and safety devices, such as deflectors and/or grass catcher, are in place and functioning properly.
Always inspect the machine to ensure that the blades and blade bolts are not worn or damaged.
Inspect the area where you will use the machine, and remove all objects that could interfere with the operation of the machine or that the machine could throw.
Contact with the moving blade will cause serious injury. Do not put your fingers under the housing.
Fuel is extremely flammable and highly explosive. A fire or explosion from fuel can burn you and others and can damage property.
To prevent a static charge from igniting the fuel, place the container and/or machine directly on the ground before filling, not in a vehicle or on an object.
Fill the fuel tank outdoors, in an open area, when the engine is cold. Wipe up any fuel that spills.
Do not handle fuel when smoking or around an open flame or sparks.
Do not remove the fuel cap or add fuel to the tank while the engine is running or hot.
If you spill fuel, do not attempt to start the engine. Avoid creating a source of ignition until the fuel vapors have dissipated.
Store fuel in an approved container and keep it out of the reach of children.
Fuel is harmful or fatal if swallowed. Long-term exposure to vapors can cause serious injury and illness.
Avoid prolonged breathing of vapors.
Keep your hands and face away from the nozzle and the fuel-tank opening.
Keep fuel away from your eyes and skin.
Type | Unleaded gasoline |
Minimum octane rating | 87 (US) or 91 (research octane; outside the US) |
Ethanol | No more than 10% by volume |
Methanol | None |
MTBE (methyl tertiary butyl ether) | Less than 15% by volume |
Oil | Do not add to the fuel |
Use only clean, fresh (no more than 30 days old), fuel from a reputable source.
Important: To reduce starting problems, add fuel stabilizer/conditioner to fresh fuel as directed by the fuel-stabilizer/conditioner manufacturer.
Clean around the fuel-tank cap and remove the cap from the tank.
Important: This machine is equipped with a premium fuel tank that uses a foam insert to prevent fuel agitation. Never remove the foam element, because it allows the engine to use all the fuel in the tank (A of Figure 10).
Note: Do not fill the fuel tank above the bottom of the fuel-tank neck (B of Figure 10).
Install the fuel-tank cap and tighten it securely by hand.
Maintenance Service Interval | Maintenance Procedure |
---|---|
Before each use or daily |
|
Important: If the oil level in the crankcase is too low or too high and you run the engine, you may damage the engine.
You may raise or lower the handle to a position comfortable for you.
Pull the handle-lock lever rearward to disengage the handle-lock pins, move the handle to 1 of 4 positions, and release the handle-lock lever to secure the handle in place. (Figure 12).
Adjusting the cutting-height levers could bring your hands into contact with a moving blade and result in serious injury.
Shut off the engine, remove the ignition key (if equipped), and wait for all moving parts to stop before adjusting the cutting height.
Do not put your fingers under the housing when adjusting the cutting height.
If the engine has been running, the muffler will be hot and can burn you.
Keep away from the hot muffler.
Note: To raise the machine, move the front and rear cutting-height levers forward; to lower the machine, move the cutting-height levers rearward. Set all the wheels to the same height unless special circumstances require otherwise.
Wear appropriate clothing, including eye protection; long pants; substantial, slip-resistant footwear; and hearing protection. Tie back long hair and do not wear loose clothing or loose jewelry.
Use your full attention while operating the machine. Do not engage in any activity that causes distractions; otherwise, injury or property damage may occur.
Do not operate the machine while ill, tired, or under the influence of alcohol or drugs.
The blade is sharp; contacting the blade can result in serious personal injury. Shut off the engine, remove the ignition key (if equipped), and wait for all moving parts to stop before leaving the operating position.
Keep bystanders out of the operating area. Keep small children out of the operating area and under the watchful care of a responsible adult who is not operating the machine. Stop the machine if anyone enters the area.
Always look down and behind you before moving the machine in reverse.
Operate the machine only in good visibility and appropriate weather conditions. Do not operate the machine when there is the risk of lightning.
Wet grass or leaves can cause serious injury if you slip and contact the blade. Avoid mowing in wet conditions.
Use extreme care when approaching blind corners, shrubs, trees, or other objects that may block your view.
Do not direct the discharge material toward anyone. Avoid discharging material against a wall or obstruction; material may ricochet toward you. Stop the blade(s) when crossing gravel surfaces.
Watch for holes, ruts, bumps, rocks, or other hidden objects. Uneven terrain could cause you to lose your balance or footing.
If the machine strikes an object or starts to vibrate, immediately shut off the engine, remove the ignition key (if equipped), wait for all moving parts to stop, and disconnect the wire from the spark plug before examining the machine for damage. Make all necessary repairs before resuming operation.
Before leaving the operating position, shut off the engine, remove the ignition key (if equipped), and wait for all moving parts to stop.
If the engine has been running, it will be hot and can severely burn you. Keep away from the hot engine.
Operate the engine only in well-ventilated areas. Exhaust gases contain carbon monoxide, which is an odorless, deadly poison.
Check the grass catcher components and the discharge chute frequently for any wear or deterioration and replace them with genuine Toro parts when necessary.
Mow across the face of slopes; never up and down. Use extreme caution when changing direction on slopes.
Do not mow on excessively steep slopes. Poor footing could cause a slip-and-fall accident.
Mow with caution near drop-offs, ditches, or embankments.
Pull the recoil handle slowly until you feel resistance, then pull it sharply. Allow the rope to return to the engine slowly.
Note: If the machine does not start after several attempts, contact an Authorized Service Dealer.
You can start the engine on an electric-start model by using either the ignition key or the recoil-start handle.
Ignition Key:
Charge the battery for 24 hours before using the machine for the first time (A of Figure 15).
Important: Do not attempt to start the engine with the blade-control bar engaged; otherwise, you may blow the fuse (B of Figure 15).
Insert the ignition key into the ignition (C of Figure 15).
Turn and hold the ignition key to the Start position; when the engine starts, release the key (D of Figure 15).
Note: Do not hold the ignition key in the Start position for longer than 5 seconds to prevent burning out the starter motor.
Recoil-Start Handle:
Turn the ignition key to the RUN position (A of Figure 16).
Important: Do not attempt to start the engine with the blade-control bar engaged; otherwise, you may blow the fuse (B of Figure 16).
Pull the recoil handle slowly to the rear until you feel resistance, then pull sharply (C of Figure 16). Allow the rope to return to the engine slowly.
To operate the self-propel drive, simply walk with your hands gripping the upper handle and your elbows at your sides, and the machine will automatically keep pace with you (Figure 17).
Note: You can self-propel the machine with the blades engaged or disengaged.
Note: Use the traction-assist handle in situations when you need more control than you have with the self-propel drive alone.
Press the toggle switch (Figure 17) to the STOP position and hold it until the engine shuts off.
Release the blade-control bar (Figure 22).
Important: When you release the blade-control bar, the blades should stop within 3 seconds. If they do not stop properly, stop using your machine immediately and contact an Authorized Service Dealer.
Maintenance Service Interval | Maintenance Procedure |
---|---|
Before each use or daily |
|
Check that the blades stop within 3 seconds of releasing the blade-control bar.
You can use the grass bag to check the blade-stop system.
Remove the rear-discharge plug.
Install the empty grass bag on the machine.
Start the engine.
Engage the blades.
Note: The bag should begin to inflate, indicating that the blades are rotating.
While watching the bag, release the blade-control bar.
Note: If the bag does not deflate within 3 seconds of releasing the blade-control bar, the blade-stop system may be deteriorating and, if ignored, could result in an unsafe operating condition. Have the machine inspected and serviced by an Authorized Service Dealer.
Shut off the engine and wait for all moving parts to stop.
Move the machine onto a paved surface in a non-windy area.
Set all 4 wheels to the 89 mm (3-1/2 inch) cutting height setting.
Take a half sheet of newspaper and crumple it into a ball small enough to go under the machine housing (about 76 mm (3 inches) in diameter).
Place the newspaper ball about 13 cm (5 inches) in front of the machine.
Start the engine.
Engage the blades.
Release the blade-control bar and begin counting out 3 seconds.
On the count of 3, push the machine quickly forward over the newspaper.
Shut off the engine and wait for all moving parts to stop.
Go to the front of the machine and check the newspaper ball.
Note: If the newspaper ball did not go under the machine, repeat steps 4 through 10.
If the newspaper is unravelled or shredded, the blades did not stop properly, which could result in an unsafe operating condition. Contact an Authorized Service Dealer.
This machine comes from the factory ready to recycle grass and leaf clippings back into the lawn. To prepare the machine to recycle, do the following:
If the side-discharge chute is on the machine, remove it and lower the side-discharge deflector; refer to Removing the Side-Discharge Chute.
If the grass bag is on the machine, remove it; refer to Removing the Grass Bag.
If the rear-discharge plug is not installed, grip it by the handle, raise the rear deflector, and insert it into the rear-discharge chute until the latch locks into place; refer to Figure 22.
Operating the machine to recycle lawn clippings without the plug in place allows objects to be thrown toward you or bystanders. Also, contact with the blades could occur. Thrown objects or blade contact can cause serious injury or death.
Ensure that the rear-discharge plug is in place before you recycle the clippings. Never engage the blades without either the rear-discharge plug or the grass bag installed on the machine.
Use the grass bag when you want to collect grass and leaf clippings from the lawn.
If the side-discharge chute is on the mower, remove it before bagging the clippings; refer to Removing the Side-Discharge Chute.
Raise and hold up the rear deflector (A of Figure 24).
Remove the rear-discharge plug by pulling down on the latch with your thumb and pulling the plug out from the machine (B of Figure 24).
Install the bag rod into the notches at the base of the handle and rock the bag back and forth to ensure that the rod is seated at the bottom of both notches (C of Figure 24)
Lower the rear deflector until it rests on the grass bag.
To remove the bag, reverse the steps in Installing the Grass Bag.
Use the side discharge for cutting very tall grass.
If the bag is on the machine, remove it and insert the rear-discharge plug; refer to Removing the Grass Bag before side-discharging the clippings.
Important: Ensure that the rear-discharge plug is in place before you recycle the clippings (Figure 23).
To remove the side-discharge chute, reverse the steps in Installing the Side-Discharge Chute.
Inspect the area where you will use the machine and remove all objects that the machine could throw.
Avoid striking solid objects with the blades. Never deliberately mow over any object.
If the machine strikes an object or starts to vibrate, immediately shut off the engine, wait for all moving parts to stop, remove the key (if equipped), disconnect the wire from the spark plug, and examine the machine for damage.
For best performance, install new Toro blades before the cutting season begins or when necessary.
Cut only about a third of the grass blade at a time. Do not cut below 51 mm (2 inches) unless the grass is sparse or it is late fall when grass growth begins to slow down.
When cutting grass over 15 cm (6 inches) tall, mow at the highest cutting height setting and walk slower; then mow again at a lower setting for the best lawn appearance. If the grass is too long, the machine may plug and cause the engine to stall.
Wet grass and leaves tend to clump on the yard and can cause the machine to plug or the engine to stall. Avoid mowing in wet conditions.
Be aware of a potential fire hazard in very dry conditions, follow all local fire warnings, and keep the machine free of dry grass and leaf debris.
Alternate the mowing direction. This helps disperse the clippings over the lawn for even fertilization.
If the finished lawn appearance is unsatisfactory, try 1 or more of the following:
Replace the blades or have them sharpened.
Walk at a slower pace while mowing.
Raise the cutting height on your machine.
Cut the grass more frequently.
Overlap cutting swaths instead of cutting a full swath with each pass.
After cutting the lawn, ensure that half of the lawn shows through the cut leaf cover. You may need to make more than a single pass over the leaves.
If there are more than 13 cm (5 inches) of leaves on the lawn, mow at a higher cutting height and then again at the desired cutting height.
Slow down your mowing speed if the machine does not cut the leaves finely enough.
Always shut off the machine, remove the ignition key (if equipped), wait for all moving parts to stop, and allow the machine to cool before adjusting, servicing, cleaning, or storing it.
Clean grass and debris from the machine to help prevent fires. Clean up oil or fuel spills.
Never store the machine or fuel container where there is an open flame, spark, or pilot light, such as on a water heater or on other appliances.
Remove the ignition key (if equipped) before loading the machine for hauling.
Use care when loading or unloading the machine.
Secure the machine from rolling.
Maintenance Service Interval | Maintenance Procedure |
---|---|
After each use |
|
Move the machine to a level surface.
Shut off the engine and wait for all moving parts to stop before leaving the operating position.
Lower the machine to its lowest cutting-height setting. Refer to Adjusting the Cutting Height.
Attach a hose to the washout fitting, and turn the water on high (Figure 26).
Note: Spread petroleum jelly on the washout fitting O-ring to make the coupling slide on easier and protect the O-ring.
Start the engine, engage the blade-control lever, and let the machine run for 1 to 3 minutes with the blades turning.
Disengage the blade-control lever, shut off the engine, and wait for all moving parts to stop.
Shut off the water and remove the coupling from the washout fitting.
Note: If the machine is not clean after a single washing, soak it and let it stand for 30 minutes. Then repeat the process.
Run the machine again and engage the blades for 1 to 3 minutes to remove the excess water.
A broken or missing washout fitting could expose you and others to thrown objects or blade contact. Contact with a blade or thrown debris can cause injury or death.
Replace a broken or missing washout fitting immediately, before using the machine again.
Never put your hands or feet under the machine or through openings in the machine.
Folding or unfolding the handle improperly can damage the cables, causing an unsafe operating condition.
Do not damage the cables when folding or unfolding the handle.
If a cable is damaged, contact an Authorized Service Dealer.
Maintenance Service Interval | Maintenance Procedure |
---|---|
After the first 5 hours |
|
Before each use or daily |
|
After each use |
|
Every 25 hours |
|
Every 50 hours |
|
Every 200 hours |
|
Yearly |
|
Yearly or before storage |
|
Important: Refer to your engine owner’s manual for additional maintenance procedures.
Always shut off the machine, wait for all moving parts to stop, and allow the machine to cool before adjusting, servicing, cleaning, or storing it.
Disconnect the spark-plug wire from the spark plug and remove the ignition key (if equipped) before performing any maintenance procedure.
Wear gloves and eye protection when servicing the machine.
The blade is sharp; contacting the blade can result in serious personal injury. Wear gloves when servicing the blade. Do not repair or alter the blade(s).
Never tamper with safety devices. Check their proper operation regularly.
Tipping the machine may cause the fuel to leak. Fuel is flammable and explosive, and can cause personal injury. Run the engine dry or remove the fuel with a hand pump; never siphon the fuel.
To ensure optimum performance of the machine, use only genuine Toro replacement parts and accessories. Replacement parts and accessories made by other manufacturers could be dangerous, and such use could void the product warranty.
Shut off the engine, remove the ignition key (if equipped), and wait for all moving parts to stop.
Disconnect the spark-plug wire from the spark plug (Figure 28).
After performing the maintenance procedure(s), connect the spark-plug wire to the spark plug.
Important: Before tipping the machine to change the oil or replace the blades, allow the fuel tank to run dry through normal usage. If you must tip the machine prior to running out of fuel, use a hand fuel pump to remove the fuel. Always tip the machine onto its side, with the dipstick down.
Tipping the machine may cause the fuel to leak. Fuel is flammable, explosive, and can cause personal injury.
Run the engine dry or remove the fuel with a hand pump; never siphon.
Maintenance Service Interval | Maintenance Procedure |
---|---|
Before each use or daily |
|
Every 50 hours |
|
Every 200 hours |
|
Yearly |
|
Loosen the fastener and remove the air-filter cover (Figure 29).
Remove and inspect the filter.
If the filter is damaged or is wet with oil or fuel, replace it.
If the filter is dirty, tap it on a hard surface several times or blow the debris outward from the interior of the filter using compressed air at less than 207 kPa (30 psi).
Note: Do not brush or blow dirt from the outside of the filter; either forces dirt into the fibers.
Clean the air-filter body and cover using a damp rag. Keep dirt away from the air opening.
Install the filter onto the base.
Install the cover and screw the fastener down securely.
Maintenance Service Interval | Maintenance Procedure |
---|---|
After the first 5 hours |
|
Every 50 hours |
|
Yearly |
|
Note: Run the engine a few minutes before changing the oil to warm it. Warm oil flows better and carries more contaminants.
Engine oil capacity | 0.53 L (18 fl oz)* |
Oil viscosity | SAE 30 or SAE 10W-30 detergent oil |
API service classification | SJ or higher |
*There is residual oil in the crankcase after you drain the oil. Do not pour the entire capacity of oil into the crankcase. Fill the crankcase with oil as directed in the following steps.
Move the machine to a level surface.
Refer to Preparing for Maintenance.
Remove the dipstick by rotating the cap counterclockwise and pulling it out (Figure 30).
Tip the machine onto its side (so that the air filter is up) to drain the used oil from the oil-fill tube (Figure 31).
After draining the used oil, return the machine to the operating position.
Carefully pour about 3/4 of the engine capacity of oil into the oil-fill tube.
Wait 3 minutes for the oil to settle in the engine.
Wipe the dipstick clean with a clean cloth.
Insert the dipstick into the oil-fill tube, then remove the dipstick.
Read the oil level on the dipstick (Figure 30).
If the oil level on the dipstick is too low, carefully pour a small amount of oil into the oil-fill tube, wait 3 minutes, and repeat steps 8 through 10 until the oil level on the dipstick is correct.
If the oil level on the dipstick is too high, drain the excess oil until the oil level on the dipstick is correct.
Install the dipstick into the oil-fill tube securely.
Recycle the used oil properly.
Maintenance Service Interval | Maintenance Procedure |
---|---|
Every 25 hours |
|
Yearly or before storage |
|
Charge the battery for 24 hours initially, then monthly (every 25 starts) or as needed. Always use the charger in a sheltered area, and charge the battery at room temperature (about 22°C or 70°F) whenever possible.
Note: The machine is not equipped with an alternator charging system.
Connect the charger to the wire harness located below the ignition key (Figure 32).
Plug the charger into a wall outlet.
Note: When the battery no longer holds a charge, recycle or dispose of the lead-acid battery according to local codes.
Note: Your battery charger may have a 2-color LED display that indicates the following states of charging:
A red light indicates that the charger is charging the battery.
A green light indicates that the charger is fully charged or is disconnected from the battery.
A flashing light that alternates between red and green indicates that the battery is nearly fully charged. This state lasts only a few minutes until the battery is fully charged.
If the battery does not charge or the engine does not run with the electric starter, the fuse may be blown. Replace it with a 40 A plug-in type fuse.
Important: You cannot start the machine with the electric starter or charge the battery unless a working fuse is installed.
Open the sealed fuse holder and replace the fuse (Figure 33).
Close the cover to the fuse holder, and ensure that it is sealed tightly.
Electric-start model only
Contact an Authorized Service Dealer to obtain a replacement battery.
Remove the belt cover; refer to step 1 of Servicing the Blade-Drive System.
Remove the rear-discharge plug.
Move the handle to the vertical position.
Remove the 4 small bolts that hold the rear deflector and handle-lock-lever assembly in place.
Fold the handle all the way forward.
Remove the rear deflector and handle-lock lever assembly (Figure 34).
Remove the cover from the battery.
Disconnect the leads from the battery.
Remove the battery and recycle it.
Note: Recycle the battery according to your state and local regulations.
Clean the battery-holding area on the machine housing.
Set the new battery in place on the machine housing.
Connect the leads to the new battery.
Note: Ensure that you connect the black (negative) wire to the negative (-) terminal and the red (positive) wire to the positive (+) terminal.
Install the cover onto the battery.
Note: Ensure that the cover fits properly over the wire harness.
Install the rear deflector and handle-lock-lever assembly onto the machine.
Raise the handle to the vertical position.
Secure the shroud with the 4 small bolts that you removed in step 5 of Removing the Old Battery.
Install the rear-discharge plug.
Return the handle to the operating position.
Whenever you install a new self-propel cable or if the self-propel drive is out of adjustment, adjust the self-propel drive.
Turn the adjustment nut counterclockwise to loosen the cable adjustment (Figure 35).
Adjust the tension on the cable (Figure 35) by pulling it back or pushing it forward and holding that position.
Note: Push the cable toward the engine to increase the traction; pull the cable away from the engine to decrease the traction.
Turn the adjustment nut clockwise to tighten the cable adjustment.
Note: Tighten the nut firmly with a socket or wrench.
Maintenance Service Interval | Maintenance Procedure |
---|---|
Every 50 hours |
|
Remove the blade-drive system cover (Figure 36).
Brush or blow out debris from the inside of the shield and around all the parts.
Hold a 0.25 mm (0.010 inch) feeler gauge, a piece of paper, or a note card against the wall and slide it down behind the belt tension spring.
Note: If there is a visible gap between the gauge and the spring, tighten the adjusting bolt and the nut until the paper barely slides freely in and out of the gap (Figure 37).
Important: Do not overtighten the adjusting bolt. This could damage the blade-drive belt.
Install the blade-drive system cover that you previously removed.
Maintenance Service Interval | Maintenance Procedure |
---|---|
Yearly |
|
Important: You will need a torque wrench to install the blades properly. If you do not have a torque wrench or are uncomfortable performing this procedure, contact an Authorized Service Dealer.
Examine the blades whenever you run out of fuel. If the blades are damaged or cracked, replace them immediately. If the blade edges are dull or nicked, have them sharpened and balanced, or replace them.
Important: Always wear padded gloves when working with the blade.
A worn or damaged blade can break, and a piece of the blade could be thrown toward you or bystanders, resulting in serious personal injury.
Inspect the blades periodically for wear or damage.
Replace a worn or damaged blade.
Note: Maintain sharp blades throughout the cutting season, because sharp blades cut cleanly without tearing or shredding the grass blades.
Lock the handle in the vertical position (Figure 38); refer to Adjusting the Handle Height.
Tip the machine onto its side, with the dipstick down, until the upper handle rests on the ground.
Maintenance Service Interval | Maintenance Procedure |
---|---|
Before each use or daily |
|
Inspect the cutting edges (Figure 39). If the edges are not sharp or have nicks, remove the blades and have them sharpened or replace them.
Inspect the blades themselves, especially the curved area (Figure 39). If you notice any damage, wear, or a slot forming in this area, immediately replace it with a new blade.
If you allow a blade to wear, a slot will form between the sail and flat part of the blade. Eventually a piece of the blade may break off and be thrown from under the housing, possibly resulting in serious injury to you or bystanders.
Inspect the blade periodically for wear or damage.
Never try to straighten a blade that is bent or weld a broken or cracked blade.
Replace a worn or damaged blade.
Check for bent blades; refer to Checking for Bent Blades.
Rotate the blades to the position shown in Figure 40.
Measure from a level surface to the cutting edges at locations A and B (Figure 40), and record both dimensions.
Rotate the blades so that their opposite ends are at locations A and B (Figure 40).
Repeat the measurements in step 2 and record them.
Note: If the difference between the dimensions A and B obtained in steps 2 and 4 exceeds 3 mm (1/8 inch), the blade is bent and you will need to replace it. Refer toRemoving the Blades and Installing the Blades.
A blade that is bent or damaged could break apart and could seriously injure or kill you or bystanders.
Always replace a bent or damaged blade with a new blade.
Never file or create sharp notches in the edges or surfaces of a blade.
Replace the blades when the machine hits a solid object or when a blade is out of balance or bent. Use only genuine Toro replacement blades.
Install the first blade so that it is horizontal, along with all mounting hardware as shown in Figure 42.
Note: Tighten the bolt with your fingers.
Important: Position the curved ends of the blades to point toward the machine housing. Be sure to nest the raised areas on each blade driver with the recesses in the head of its corresponding spindle, and the pins on the other side of each blade driver with the holes in its corresponding blade.
Steady each blade with a board and turn the blade bolt clockwise with a torque wrench as shown in Figure 43; torque the blade bolt to 82 N∙m (60 ft-lb).
Rotate the installed blade 1/4 turn until it is vertical, and install the other blade in the same manner as the first (refer to step 1).
Note: The blades should be perpendicular, forming an inverted “T” as shown in Figure 44.
Tighten the second blade; refer to step 2.
Rotate the blades by hand a full 360° turn to ensure that they do not touch.
Note: If the blades touch each other, they are not mounted correctly. Repeat steps 1 through 3, until the blades no longer touch each other.
Incorrectly installing the blades could damage the machine or cause an injury to you or bystanders.
Use care when installing the blades.
Store the machine in a cool, clean, dry place.
Always shut off the machine, remove the ignition key (if equipped), wait for all moving parts to stop, and allow the machine to cool before adjusting, servicing, cleaning, or storing it.
Perform the recommended annual maintenance procedures; refer to .
Clean under the machine housing; refer to Cleaning Under the Machine.
Remove chaff, dirt, and grime from the external parts of the engine, the shrouding, and the top of the machine.
Check the condition of the blades; refer to Inspecting the Blades.
Service the air filter; refer to Servicing the Air Filter.
Tighten all nuts, bolts, and screws.
Touch up all rusted or chipped paint surfaces with paint available from an Authorized Service Dealer.
Electric-start model only: Charge the battery for 24 hours, then unplug the battery charger and store the machine in an unheated area. If you must store the machine in a heated area, you must charge the battery every 90 days. Remove the key.
Fold the handle for storage; refer to Folding the Handle.
Fuel can vaporize if you store it over long periods of time and explode if it comes into contact with an open flame.
Do not store fuel over long periods of time.
Do not store the machine with fuel in the fuel tank or the carburetor in an enclosure with an open flame. (For example, a furnace or a water heater pilot light.)
Allow the engine to cool before storing it in any enclosure.
On the last refueling of the year, add fuel stabilizer to the fuel as directed by the engine manufacturer. Empty the fuel tank when mowing the last time before storing the machine.
Run the machine until the engine shuts off from running out of fuel.
Start the engine again and allow it to run until it shuts off. When you can no longer start the engine, it is sufficiently dry.
While the engine is still warm, change the engine oil; refer to Changing the Engine Oil.
Disconnect the wire from the spark plug and remove the ignition key (electric-start model only).
Remove the spark plug.
Using an oil can, add about 30 ml (1 fl oz), of motor oil to the engine through the spark-plug hole.
Slowly pull the starter rope several times to distribute oil throughout the cylinder.
Install the spark plug but do not connect the wire to the spark plug. Secure the wire so that it does not come into contact with the spark plug.
Unfold the handle; refer to Assembling and Unfolding the Handle.
Check and tighten all fasteners.
Remove the spark plug and spin the engine rapidly using the starter to blow excess oil from the cylinder.
Inspect the spark plug and replace it if it is dirty, worn, or cracked; refer to the engine owner’s manual.
Install the spark plug and tighten it to the recommended torque of 20 N∙m (15 ft-lb).
Perform any needed maintenance procedures; refer to .
Check the engine-oil level; refer to Checking the Engine-Oil Level.
Fill the fuel tank with fresh fuel; refer to Filling the Fuel Tank.
Electric-start model only: Charge the battery; refer to Charging the Battery.
Connect the wire to the spark plug.