Power Max® e24 60V Snowthrower

This machine is intended to be used by residential homeowners. It is designed primarily for removing snow from paved surfaces, such as driveways and sidewalks, and other surfaces for traffic on residential or commercial properties. It is not designed for removing materials other than snow. It is designed to use Flex-Force 60V lithium-ion battery packs. These battery packs are designed to be charged only by Flex-Force 60V lithium-ion battery chargers. Using this product for purposes other than its intended use could prove dangerous to you and bystanders.

Read this information carefully to learn how to operate and maintain your product properly and to avoid injury and product damage. You are responsible for operating the product properly and safely.

Visit www.Toro.com for product safety and operation training materials, accessory information, help finding a dealer, or to register your product.

Whenever you need service, genuine Toro parts, or additional information, contact an Authorized Service Dealer or Toro Customer Service and have the model and serial numbers of your product ready. Figure 1 identifies the location of the model and serial numbers on the product. Write the numbers in the space provided.

Important: With your mobile device, you can scan the QR code on the serial number decal (if equipped) to access warranty, parts, and other product information.

Figure 1

1. Model and serial number location

This manual identifies potential hazards and has safety messages identified by the safety-alert symbol (Figure 2), which signals a hazard that may cause serious injury or death if you do not follow the recommended precautions.

Figure 2

Safety-alert symbol

This manual uses 2 words to highlight information. Important calls attention to special mechanical information and Note emphasizes general information worthy of special attention.

WARNING—When using an electric machine, always read and follow basic safety warnings and instructions to reduce the risk of fire, electric shock, or injury, including the following:

READ ALL INSTRUCTIONS

WARNING—When using an electrical machine, basic safety precautions should always be followed to reduce the risk of fire, electric shock, or injury, including the following:

I. Training

1. The operator of the machine is responsible for any accidents or hazards occurring to others or their property.

2. Read and understand the contents of this Operator’s Manual before you start the machine. Ensure that everyone using this machine knows how to use it, knows how to shut it off quickly, and understands the warnings.

3. Do not allow children to use or play with the machine, battery pack, or the battery charger; local regulations may restrict the age of the operator.

4. Do not allow children or untrained people to operate or service this device. Allow only people who are responsible, trained, familiar with the instructions, and physically capable to operate or service the device.

5. Before using the machine, battery pack, and battery charger, read all the instructions and cautionary markings on these products.

6. Become familiar with the controls and proper use of the machine, battery pack, and battery charger.

II. Preparation

1. Keep bystanders and children out of the operating area.

2. Never allow children to operate the machine.

3. Do not operate the machine without all guards and safety devices in place and functioning properly on the machine.

4. Inspect the area where you will use the machine and remove all objects that could interfere with the operation of the machine or that the machine could throw.

5. Use only the battery pack specified by Toro. Using other accessories and attachments may increase the risk of injury and fire.

6. Plugging the battery charger into an outlet that is not 120 V can cause a fire or electric shock. Do not plug the battery charger into an outlet other than 120 V.

7. Do not use a damaged or modified battery pack or battery charger, which may exhibit unpredictable behavior that results in fire, explosion, or risk of injury.

8. If the supply cord to the battery charger is damaged, contact an Authorized Service Dealer to replace it.

9. Do not use non-rechargeable batteries.

10. Charge the battery pack with only the battery charger specified by Toro. A charger suitable for 1 type of battery pack may create a risk of fire when used with another battery pack.

11. Charge the battery pack in a well-ventilated area only.

12. Do not expose a battery pack or battery charger to fire or to temperatures higher than 68°C (154°F).

13. Follow all charging instructions and do not charge the battery pack outside of the temperature range specified in the instructions. Otherwise, you may damage the battery pack and increase the risk of fire.

14. Dress properly—Wear appropriate clothing, including eye protection; long pants; substantial, slip-resistant rubber boots; and hearing protection. Tie back long hair and do not wear loose clothing or loose jewelry that can get caught in moving parts.

III. Operation

1. Contact with the moving rotor will cause serious injury. Keep your hands and feet away from all moving parts of the machine. Keep clear of any discharge opening.

2. Stay behind the handles and away from the discharge opening while operating the machine.

3. Using this machine for purposes other than its intended use could prove dangerous to you and bystanders.

4. Prevent unintentional starting—Ensure that the electric-start key is removed from the key switch before connecting the battery pack and handling the machine.

5. Use your full attention while operating the machine. Do not engage in any activity that causes distractions; otherwise, injury or property damage may occur.

6. Disengage all clutches and shift into neutral before starting the machine.

7. Stop the machine, remove the electric-start key, remove the battery pack from the machine, and wait for all movement to stop before adjusting, servicing, cleaning, or storing the machine.

8. Remove the battery pack and electric-start key from the machine whenever you leave it unattended or before changing accessories.

9. Do not force the machine—Allow the machine to do the job better and safer at the rate for which it was designed.

10. Stay alert—Watch what you are doing and use common sense when operating the machine. Do not use the machine while ill, tired, or under the influence of alcohol or drugs.

11. Operate the machine only in good visibility and appropriate weather conditions.

12. Use extreme caution when reversing or pulling the machine toward you.

13. Keep proper footing and balance at all times, especially on slopes. Use extreme caution when changing directions on slopes. Do not operate the machine on exceedingly steep slopes. Walk, never run with the machine.

14. When not actively clearing snow, disengage power to the auger.

15. Do not direct the discharge material toward anyone. Avoid discharging material against a wall or obstruction; material may ricochet toward you. Stop the machine when crossing gravel surfaces.

16. Exercise extreme caution when operating the machine on or crossing gravel drives, walks, or roads. Stay alert for hidden hazards or traffic.

17. If the machine strikes an object or starts to vibrate, immediately shut off the machine, remove the key, remove the battery pack, and wait for all movement to stop before examining the machine for damage. Make all necessary repairs before resuming operation.

18. Shut off the machine whenever you leave the operating position for any reason.

19. Shut off the machine and remove the key before unclogging the machine and always use a stick or a cleanout tool to remove the clog.

20. Stop the machine and remove the electric-start key before loading the machine for hauling.

21. Under abusive conditions, the battery pack may eject liquid; avoid contact. If you accidently come into contact with the liquid, flush with water. If the liquid contacts your eyes, seek medical help. Liquid ejected from the battery pack may cause irritation or burns.

22. Never operate the machine at high transport speeds on slippery surfaces.

IV. Maintenance and Storage

1. Stop the machine, remove the electric-start key, remove the battery pack from the machine, and wait for all movement to stop before adjusting, servicing, cleaning, or storing the machine.

2. Do not attempt to repair the machine except as indicated in the instructions. Have an Authorized Service Dealer perform service on the machine using identical replacement parts.

3. Wear gloves and eye protection when servicing the machine.

4. When servicing the rotor, be aware that the rotor can still move even though the power source is off.

5. For best performance, use only genuine Toro replacement parts and accessories. Other replacement parts and accessories could be dangerous, and such use could void the product warranty.

6. Maintain the machine—Keep handles dry, clean, and free from oil and grease. Keep guards in place and in working order. Use identical replacement parts only.

7. Check all fasteners at frequent intervals for proper tightness to ensure that the machine is in safe working condition.

8. Check the machine for damaged parts. Check for misaligned and binding moving parts, broken parts, mounting, and any other condition that may affect its operation. Unless indicated in the instructions, have an Authorized Service Dealer repair or replace a damaged guard or part.

9. When the battery pack is not in use, keep it away from metal objects such as paper clips, coins, keys, nails, and screws that can make a connection from 1 terminal to another. Shorting the battery terminals may cause burns or a fire.

10. When you are not using the machine, store it indoors in a dry, secure place out of the reach of children.

11. When storing the machine for more than 30 days, refer to Before storage for important information.

12. CAUTION—A mistreated battery pack may present a risk of fire or chemical burn. Do not disassemble the battery pack. Do not heat the battery pack above 68°C (154°F) or incinerate it. Replace the battery pack with a genuine Toro battery pack only; using another type of battery pack may cause a fire or explosion. Keep battery packs out of the reach of children and in the original packaging until you are ready to use them.

13. Do not dispose of the battery in a fire. The cell may explode. Check with local codes for possible special disposal instructions.

SAVE THESE

INSTRUCTIONS

Safety and Instructional Decals

Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing.

94-8072

121-6817

1. Cutting/dismemberment hazard of hand or foot, impeller and auger—keep bystanders away.

121-6823

1. Fast
2. Forward speeds
3. Slow
4. Reverse speeds

137-6198

1. Cutting/dismemberment hazard of the fingers or hand, impeller—do not place your hand in the chute.
2. Warning—shut off the motor before using the tool to clear the chute.

121-1240

1. Traction drive—squeeze the lever to engage; release the lever to disengage.
2. Warning—read the Operator’s Manual.
3. Cutting/dismemberment hazard of hand, impeller—do not place your hand in the chute; shut off the motor before leaving the operating position; use the tool to clear the chute.
4. Cutting/dismemberment hazard of hand, impeller—stay away from moving parts; keep all guards and shields in place; remove the key and read the Operator’s Manual before performing maintenance.
5. Thrown object hazard—keep bystanders away.
6. Auger/impeller drive—squeeze the lever to engage; release the lever to disengage.

137-9462

137-9463

1. The battery pack is charging.
2. The battery pack is fully charged.
3. The battery pack is over or under the appropriate temperature range.
4. Battery pack charging fault

137-9455

1. Read the Operator’s Manual.
2. Keep away from open fire or flames.
3. Do not expose to rain.

137-9461

1. Battery charge status

133-8061

Important: The battery pack is not fully charged when you purchase it. Before using the machine for the first time, refer to Charging the Battery Pack.

Mounting the Battery Charger (Optional)

Parts needed for this procedure:

Mounting hardware (not included)

2

If desired, mount the battery charger securely on a wall using the wall-mount key holes on the back of the charger.

Mount it indoors (such as a garage or other dry place), near a power outlet, and out of the reach of children.

Refer to Figure 3 for assistance in mounting the charger.

Slide the charger over the appropriately positioned hardware to secure the charger in place (hardware not included).

Figure 3

Installing the Chute

Figure 4

Installing the Upper Handle

Figure 5

Installing the Traction-Control Linkage

Figure 6

Installing the Chute-Control Rod

Figure 7

Installing the Snow-Cleanout Tool

Figure 8

Checking the Tire Pressure

Figure 9

Figure 11

1. Handgrip (2)
2. Auger/impeller lever
3. Lock switch
4. Speed-selector lever
5. Quick Stick^® discharge-chute control
6. Traction lever
7. Main battery-compartment lid
8. Electric-start key
9. Chute deflector
10. Discharge chute
11. Scraper
12. Auger
13. Skid (2)
14. Control panel
15. Secondary battery-compartment lid
16. Snow-cleanout tool

Figure 12

1. Battery charge lights
2. ECO button
3. Key switch in OFF position

Figure 13

1. Snow-cleanout tool (attached to the handle)

Figure 14

1. Battery charger Model 88602 (included with Model 39924)
2. Battery pack Model 88660 (2 included with Model 39924)

Battery Pack

Battery Charger

Appropriate Temperature Ranges

*Charging time will increase if you do not charge the battery within this range.

Store the machine, battery pack, and battery charger in an enclosed clean, dry area.

Note: Determine the left and right sides of the machine from the normal operating position.

Before Operation

Installing the Battery Pack

1. Ensure that the vents on the battery packs are clear of any dust and debris.

2. Lift up the battery-compartment lid.

3. Line up the cavity in the battery pack with the tongue on the machine and slide the battery pack into the compartment until it lock into place (Figure 9).

4. Close the battery-compartment lid.

5. Repeat for the other 2 battery cavities (if needed).

   Note: The combined amp hours of all the installed batteries must add up to 6.0 or greater, otherwise the machine can not start.

   Note: If the battery-compartment lid does not close completely, the battery is not fully installed.

Figure 15

Checking the State of Charge

You can view the exact state of charge of each installed battery; turn the key to the ACCESSORY position (Figure 16). The position of each set of lights corresponds to the related battery cavity. If the battery state of charge is too low and needs to be charged, or if there is no battery in the corresponding cavity, the battery presence light does not turn on.

Figure 16

1. State-of-charge lights
2. Battery presence lights
3. Key switch in the ACCESSORY position

During Operation

Starting the Machine

Note: Use the battery pack only in temperatures that are within the appropriate range; refer to Specifications.

1. Ensure that the battery pack(s) are installed in the machine; refer to Installing the Battery Pack.

2. Insert the electric-start key into the control panel

3. Turn the key to the RUN position to turn on the machine (Figure 17).

   

   Figure 17

   1. Key switch in ON position

Activating ECO Mode

Using ECO mode may extend battery life by reducing rotor speed; use ECO mode whenever you are moving light snow, or moving snow a short distance. Activate ECO mode using the ECO button as shown in Figure 18.

Figure 18

1. ECO mode button

Charging the Battery Pack

Important: The battery pack is not fully charged when you purchase it. Before using the tool for the first time, place the battery pack in the charger and charge it until the LED display indicates the battery pack is fully charged. Read all safety precautions.

Important: Charge the battery pack only in temperatures that are within the appropriate range; refer to Specifications.

Note: At any time, press the battery-charge-indicator button on the battery pack to display the current charge (LED indicators).

1. Ensure that the vents on the battery charger are clear of any dust and debris.

   

   Figure 19

   1. Battery pack cavity
   2. Battery pack terminals
   3. Battery-charge-indicator button
   4. LED indicators (current charge)
   5. Handle
   6. Charger LED indicator light
   7. Charger venting areas

2. Line up the cavity in the battery pack (Figure 19) with the tongue on the charger.

3. Slide the battery pack into the charger until it is fully seated (Figure 19).

4. To remove the battery pack, slide the battery backward out of the charger.

5. Refer to the following table to interpret the LED indicator light on the battery charger.

   Indicator light	Indicates
   Off	No battery pack inserted
   Green blinking	Battery pack is charging
   Green	Battery pack is charged
   Red	Battery pack and/or battery charger is over or under the appropriate temperature range
   Red blinking	Battery pack charging fault*

*Refer to for more information.

Important: The battery can be left on the charger for short periods between uses.If the battery will not be used for longer periods, remove the battery from the charger; refer to Before storage.

Operating the Traction Drive

Caution

If the traction drive is not properly adjusted, the machine may move in the direction opposite of what you intended, causing injury and/or property damage.

Carefully check the traction drive and adjust it properly, if necessary; refer to Checking the Operation of the Traction Drive for more information.

Important: If the machine moves when the traction lever is in the released position, check the traction cable; refer to Checking the Operation of the Traction Drive or take the machine to an Authorized Service Dealer for service.

1. To engage the traction drive, squeeze the left (traction) lever to the handgrip (Figure 20).

   

   Figure 20

2. To stop the traction drive, release the traction lever.

Operating the Speed Selector

The speed selector has 6 forward and 2 reverse gears. To change speeds, release the traction lever and shift the speed-selector lever to the desired position (Figure 21). The lever locks in a notch at each speed selection.

Figure 21

Operating the Auger/Impeller Drive

1. To engage the auger/impeller drive, move back the lock switch on the lever, then squeeze the right (auger/impeller) lever to the handgrip (Figure 22).

   

   Figure 22

2. To stop the auger and impeller, release the right lever.

   Important: When you engage both the auger/impeller lever and the traction lever, the traction lever locks the auger/impeller lever down, freeing your right hand. To release both levers, simply release the left (traction) lever.

3. If the auger and impeller continue to rotate when you release the auger/impeller lever, do not operate the machine. Check the auger/impeller cable; refer toChecking and Adjusting the Auger/Impeller Cable and adjust it if necessary. Otherwise, take the machine to an Authorized Service Dealer for service.

   Warning

   If the auger and impeller continue to rotate when you release the auger/impeller lever, you could seriously injure yourself or others.

   Do not operate the machine. Take it to an Authorized Service Dealer for service.

Operating the Quick Stick®

Hold the blue trigger cap down to use the Quick Stick to move the discharge chute and the chute deflector. Release the trigger cap to lock the discharge chute and chute deflector into position (Figure 23).

Figure 23

Moving the Discharge Chute

Hold the blue trigger cap down and move the Quick Stick to the left to move the discharge chute to the left; move the Quick Stick to the right to move the discharge chute to the right (Figure 24).

Figure 24

• If the chute does not turn as far to the left as it does to the right, ensure that the cable is routed to the inside of the handles. Refer to Installing the Upper Handle.

• If the chute does not move, or does not lock into place when you release the trigger cap, you must adjust the discharge-chute latch cable.

Moving the Chute Deflector

Hold the blue trigger cap down and move the Quick Stick forward to lower the chute deflector; move it rearward to raise the chute deflector (Figure 25).

Figure 25

Clearing a Clogged Discharge Chute

Warning

If the auger/impeller is running but there is no snow coming out of the discharge chute, the discharge chute may be clogged.

Never use your hands to clear a clogged discharge chute. This could result in personal injury.

• To unclog the discharge chute, stay in the operating position and release the left (traction) lever. While running the auger/impeller, push down on the handles to raise the front of the machine a few centimeters (inches) off the pavement. Then lift the handles quickly to bump the front of the machine on the pavement. Repeat if necessary until a stream of snow comes out the discharge chute.

• If you cannot unclog the discharge chute by bumping the front of the machine, shut off the machine, wait for all moving parts to stop, and use the snow-cleanout tool (Figure 13).

  Important: Unclogging the discharge chute by bumping the front of the machine on the pavement may cause the skids to move. Adjust the skids and tighten the skid bolts securely; refer to Checking and Adjusting the Skids and Scraper.

Operating Tips

Danger

When the machine is in operation, the impeller and auger rotate and can injure or amputate hands or feet.

• Before adjusting, cleaning, inspecting, troubleshooting, or repairing the machine, shut off the machine and wait for all moving parts to stop. Remove the key and the battery from the machine to prevent someone from accidentally starting the machine.

• Remove any obstructions from the discharge chute; refer to Clearing a Clogged Discharge Chute. Use the snow-cleanout tool (Figure 13), not your hands, to remove an obstruction from the discharge chute.

• Stay behind the handles and away from the discharge opening while operating the machine.

• Keep your face, hands, feet, and any other part of your body or clothing away from concealed, moving, or rotating parts.

Warning

The impeller can throw stones, toys, and other foreign objects and cause serious personal injury to you or bystanders.

• Keep the area to be cleared free of all objects that the auger could pick up and throw.

• Keep all children and pets away from the area of operation.

For best results, consider the following:

• If the machine slows down under a load or the wheels slip, shift the machine into a lower gear; refer to Operating the Speed Selector.

• If the front of the machine rides up, shift the machine into a lower gear. If the front continues to ride up, lift up on the handles.

• Remove the snow as soon as possible after it falls.

• Push the machine forward, but allow it to work at its own pace.

• Overlap each swath to ensure complete snow removal.

• Discharge the snow downwind whenever possible.