Titan ZX4875, ZXM4875, ZXM5475, or ZXM6075 Riding Mower
Disclaimers and Regulatory Information
This product complies with all relevant European directives; for details, please see the separate product specific Declaration of Conformity (DOC) sheet.
Gross or Net Torque: The gross or net torque of this engine was laboratory rated by the engine manufacturer in accordance with the Society of Automotive Engineers (SAE) J1940 or J2723. As configured to meet safety, emission, and operating requirements, the actual engine torque on this class of mower will be significantly lower. Please refer to the engine manufacturers information included with the machine.
 
 
 
Introduction
 

Intended Use

This rotary-blade, riding lawn mower is intended to be used by homeowners in residential applications. It is designed primarily for cutting grass on well-maintained lawns. Using this product for purposes other than its intended use could prove dangerous to you and bystanders.
Read this information carefully to learn how to operate and maintain your product properly and to avoid injury and product damage. You are responsible for operating the product properly and safely.

Getting Help

Graphic
G451770
Visit www.Toro.com for product safety and operation training materials, accessory information, help finding a dealer, or to register your product.
Whenever you need service, genuine Toro parts, or additional information, contact an Authorized Service Dealer or Toro Customer Service and have the model and serial numbers of your product ready. These numbers are located on the serial plate on your product . Write the numbers in the space provided.
Important  
With your mobile device, you can scan the QR code on the serial number decal (if equipped) to access warranty, parts, and other product information.
 
Model Number:
Serial Number:

Manual Conventions

This manual identifies potential hazards and has safety messages identified by the safety-alert symbol, which signals a hazard that may cause serious injury or death if you do not follow the recommended precautions.
Graphic
G405934
This manual uses 2 words to highlight information. Important calls attention to special mechanical information and Note emphasizes general information worthy of special attention.
Safety Alert Classifications
The safety-alert symbol shown in this manual and on the machine identifies important safety messages that you must follow to prevent accidents.
Safety-alert symbol appears above information that alerts you to unsafe actions or situations and is followed by the word DANGER, WARNING, or CAUTION.
Danger
Danger indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
 
Warning
Warning indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
 
Caution
Caution indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
 
 
 
 
Safety
 

General Safety

This product is capable of amputating hands and feet and of throwing objects. Always follow all safety instructions to avoid serious personal injury or death.

Slope Indicator

You may copy this page for personal use.
Graphic
G011841s
  1. The maximum slope you can operate the machine on is 15 degrees. Use the slope chart to determine the degree of slope of hills before operating. Do not operate this machine on a slope greater than 15 degrees. Fold along the appropriate line to match the recommended slope.
  2. Align this edge with a vertical surface, a tree, building, fence pole, etc.
  3. Example of how to compare slope with folded edge

Safety and Instructional Decals

Image
Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing.
Decal Part: 117-1194
Graphic
s_decal117-1194
  1.  Belt routing
  2.  Engine
Decal Part: 130-0731
Graphic
s_decal130-0731
  1.  Warningthrown object hazard; keep the deflector in place.
  2.  Cutting hazard of hand or foot, mower bladekeep away from moving parts.
Decal Part: 130-0765
Graphic
s_decal130-0765
  1.  Read the Operators Manual.
  2.  Height-of-cut selection
  3.  Remove the key before performing maintenance.
Decal Part: 132-0872
Graphic
s_decal132-0872
  1.  Thrown object hazardkeep bystanders away.
  2.  Thrown object hazard, mowerdo not operate the machine with an open deck; use a bagger or a deflector.
  3.  Cutting/dismemberment hazard of hands or feet, mower bladestay away from moving parts.
  4.  Entanglement hazard of hands, beltstay away from moving parts; keep all guards and shields in place.
Decal Part: 139-2394
Graphic
s_decal139-2394
  1.  Traction controls
  2.  Fast
  3.  Slow
  4.  Neutral
  5.  Reverse
  6.  Parking brake
Decal Part: 139-2395
Graphic
s_decal139-2395
  1.  Parking brake
  2.  Fast
  3.  Slow
  4.  Neutral
  5.  Reverse
  6.  Traction controls
Decal Part: 144-5288
Graphic
s_decal144-5288
  1.  Warningread the Operators Manual.
  2.  Cutting/dismemberment hazard of the fingers or handkeep hands away from moving parts; keep all guards and shields in place.
  3.  Thrown object hazardkeep bystanders away; pick up debris; keep the deflector in place.
  4.  Runover hazarddo not carry passengers; look behind you and down when moving in reverse.
  5.  Tipping hazardwhen loading onto a trailer, do not use dual ramps; only use a singular ramp wide enough for the machine; do not use a ramp with a slope greater than 15°; back up the ramp (in reverse) and drive forward off the ramp.
  6.  Tipping hazarddo not use the machine near drop-offs with slopes greater than 15°; only operate across slopes less than 15°.
Note: This machine complies with the industry standard stability test in the static lateral and longitudinal tests with the maximum recommended slope indicated on the decal. Review the instructions for operating the machine on slopes in the Operators Manual as well as the conditions in which you would operate the machine to determine whether you can operate the machine in the conditions on that day and at that site. Changes in the terrain can result in a change in slope operation for the machine.
Decal Part: 147-2399
Graphic
s_decal147-2399
  1.  Read the Operators Manual.
  2.  WarningFill to bottom of filler neck; warningdo not overfill the tank.
Decal Part: 147-7571
Graphic
s_decal147-7571
  1.  Fast
  2.  Slow
Decal Part: 147-7574
MyRIDE models only
Graphic
s_decal147-7574
Decal Part: 161-6207
Graphic
decal161-6207
  1.  Bypass lever position for pushing the machine
  2.  Bypass lever position for operating the machine
Decal Part: 161-6208
Graphic
decal161-6208
  1.  Height of cut
  2.  To release the transport lockpush the deck-lift pedal forward, move the transport-lock lever forward, and then move the deck-lift pedal rearward toward the desired height of cut.
 
 
 
Product Overview
 
Graphic
G453237
  1. Engine
  2. MyRide® suspension adjustment lever (machines with MyRide suspension only)
  3. Control panel
  4. Transport lock lever
  5. Deflector
  6. Height-of-cut pin
  7. Deck-lift pedal
  8. Anti-scalp roller
  9. Front caster wheel
  10. Motion-control lever
  11. Fuel-tank cap
Control Panel
Graphic
G453238
  1.  Throttle control
  2.  Choke control
  3.  Key switch
  4.  Blade-control switch (power takeoff)
  5.  Hour meter
Key Switch
Use the key switch to start or shut off the machine.
Graphic
G375755s
  1.  Shut off the engine
  2.  Run the engine
  3.  Start engine
Throttle Control
Graphic
G450843
The throttle controls the engine speed, and it has a continuous-variable setting from the Slow to Fast position.
Blade-Control (PTO) Switch
Graphic
G428617
The blade-control switch, represented by a power-takeoff (PTO) symbol, engages and disengages power to the mower blades.
Choke Control
Use the choke control to aid in starting a cold engine.
Graphic
G419508
  1. Engaged
  2. Disengaged
Hour Meter
The hour meter records the number of hours the engine is running. Use these times for scheduling regular maintenance.

Motion-Control Levers

Use the motion-control levers to drive the machine forward, reverse, and turn either direction.
Park Position
Graphic
G438246
Move the motion-control levers outward from the center to the Park position to engage the parking brake when stopping or exiting the machine.

MyRide® Suspension Adjustment Lever

For Machines with the MyRide Suspension System
Use the adjustment lever to adjust the seat suspension for a smooth and comfortable ride.
Graphic
G292102s
  1.  Adjustment lever
  2.  Softer suspension
  3.  Firmer suspension

Height-of-Cut Pin

The height-of-cut pin works with the foot pedal to lock the deck in a specific cutting height. Adjust the height of cut only when the machine is not moving.

Deck-Lift Pedal

Use the deck-lift pedal to briefly raise the mower deck from the seated position to avoid obstacles or when adjusting the height of cut.

Transport-Lock Lever

Use the transport-lock lever to release the mower deck from the Transport (fully raised) position.
Graphic
G453249

Fuel Gauge

The fuel gauge displays the amount of fuel in the tank.
Graphic
G456141
Specifications
Note: Specifications and design are subject to change without notice.
 
Model 76420
Model 76425
Model 76530
Model 76635
Cutting width
123 cm (48 inches)
123 cm (48 inches)
137 cm (54 inches)
152 cm (60 inches)
Width with deflector down
163 cm (64 inches)
163 cm (64 inches)
178 cm (70 inches)
192 cm (75-1/2 inches)
Width with deflector up
138 cm (54-1/2 inches)
138 cm (54-1/2 inches)
152 cm (60 inches)
166 cm (65-1/2 inches)
Length
208 cm (82 inches)
208 cm (82 inches)
208 cm (82 inches)
208 cm (82 inches)
Height
124 cm (49 inches)
127 cm (50 inches)
127 cm (50 inches)
127 cm (50 inches)
Weight
338 kg (746 lb)
354 kg (781 lb)
354 kg (781 lb)
371 kg (817 lb)
Attachments/Accessories
A selection of Toro approved attachments and accessories is available for use with the machine to enhance and expand its capabilities. Contact your Authorized Service Dealer or authorized Toro distributor or go to www.Toro.com for a list of all approved attachments and accessories.
To ensure optimum performance and continued safety certification of the machine, use only genuine Toro replacement parts and accessories.
 
 
 
Operation
 

Before Operation

Before Operation Safety
  • Do not allow children or untrained people to operate or service the machine. Local regulations may restrict the age of the operator. The owner is responsible for training all operators and mechanics.
  • Inspect the area where you will use the machine and remove all objects that could be thrown or could interfere with the operation of the machine.
  • Evaluate the terrain to determine the appropriate equipment and any attachments or accessories required to operate the machine properly and safely.
  • Do not carry passengers on the machine.
  • Become familiar with the safe operation of the equipment, operator controls, and safety signs.
  • Check that operator-presence controls, safety switches, and guards are attached and working properly. Do not operate the machine unless they are functioning properly.
  • Wear appropriate clothing, including eye protection; long pants; substantial, slip-resistant footwear; and hearing protection. Tie back long hair and do not wear loose clothing or loose jewelry.
  • Do not operate the machine unless all guards and safety devices, such as the deflectors and the entire grass catcher, are in place and functioning properly. Replace worn or deteriorated parts when necessary.
  • Shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operators position. Wait for the machine to cool before servicing, adjusting, fueling, cleaning, or storing it.
    Warning
    Contacting the blade can result in serious personal injury.
    When you shut off the engine, the blade(s) should stop. If not, stop using your machine immediately and contact an Authorized Service Dealer.
     
  • Before mowing, inspect the machine to ensure that the cutting assemblies are working properly.
  • Keep bystanders, particularly children, and pets away from the machine during operation. Shut off the machine and attachment(s) if anyone enters the area.
Fuel Safety
  • Fuel is extremely flammable and highly explosive. A fire or explosion from fuel can burn you and others and can damage property.
    • To prevent a static charge from igniting the fuel, place the container and/or machine directly on the ground before filling, not in a vehicle or on an object.
    • Fill the fuel tank outdoors on level ground, in an open area, and when the engine is cold. Wipe up any fuel that spills.
    • Do not handle fuel when smoking or around an open flame or sparks.
    • Do not remove the fuel cap or add fuel to the tank while the engine is running or hot.
    • If you spill fuel, do not attempt to start the engine. Avoid creating a source of ignition until the fuel vapors have dissipated.
    • Store fuel in an approved container and keep it out of the reach of children.
  • Do not overfill the fuel tank. Replace the fuel cap and tighten it securely.
  • In certain conditions during fueling, static electricity can be released, causing a spark that can ignite fuel vapors.
  • Do not fill containers inside a vehicle or on a truck or trailer bed with a plastic liner. Always place containers on the ground and away from your vehicle before filling.
  • Remove the equipment from the truck or trailer and refuel it while it is on the ground. If this is not possible, then refuel from a portable container rather than from a fuel-dispenser nozzle.
  • Keep the fuel-dispenser nozzle in contact with the rim of the fuel tank or container opening at all times until fueling is complete. Do not use a nozzle lock-open device.
  • Fuel is harmful or fatal if swallowed. Long-term exposure to vapors can cause serious injury and illness.
    • Avoid prolonged breathing of vapors.
    • Keep your hands and face away from the nozzle and the fuel-tank opening.
    • Keep fuel away from your eyes and skin.
  • Clean up any spilled fuel.
  • Do not store the machine or fuel container where there is an open flame, spark, or pilot light, such as on a water heater or on other appliances.
  • Do not operate the machine without the entire exhaust system in place and in proper working condition.
Fuel
Fuel Specifications
Capacity
19 L (5 US gallons)
Type
Unleaded gasoline
Minimum octane rating
87 (US) or 91 (research octane; outside the US)
Ethanol
No more than 10% by volume
Methanol
None
MTBE (methyl tertiary butyl ether)
Less than 15% by volume
Oil
Do not add to the fuel
Use only clean, fresh (no more than 30 days old), fuel from a reputable source.
Important  
To reduce starting problems, add fuel stabilizer/conditioner to fresh fuel as directed by the fuel-stabilizer/conditioner manufacturer.
 
Filling the Fuel Tank
  1. Park the machine on a level surface.
  2. Move the motion-control levers outward to the Park position.
  3. Shut off the engine and remove the key.
  4. Clean around the fuel-tank cap and fill the fuel tank.
    Important  
    Fill the fuel tank to the bottom of the filler neck. Do not fill the fuel tank completely full.
     
    Graphic
    G453272
Performing Daily Maintenance
Before starting the machine each day, perform the Each Use/Daily procedures listed in the Maintenance Schedule.
Break-In Time
New engines take time to develop full power. Mower decks and drive systems have higher friction when new, placing additional load on the engine. Allow 40 to 50 hours of break-in time for new machines to develop full power and best performance.
Safety-Interlock System
The safety-interlock system is designed to prevent the engine from starting unless:
  • The blade-control switch (PTO) is disengaged.
  • The motion-control levers are in the Park position.
The safety-interlock system also is designed to shut off the engine whenever the control levers are out of the Park position and you rise from the seat.
Warning
If the safety-interlock switches are disconnected or damaged, the machine could operate unexpectedly, causing personal injury.
  • Do not tamper with the interlock switches.
  • Check the operation of the interlock switches daily and replace any damaged switches before operating the machine.
 
Testing the Safety-Interlock System
Test the safety-interlock system before you use the machine each time. If the safety system does not operate as described below, have an Authorized Service Dealer repair the safety system immediately.
  1. Sit on the seat, move the motion-control levers to the Park position, and move the blade-control switch to the On position. Try starting the engine; the engine should not crank.
    Graphic
    G451953
  2. Sit on the seat and move the blade-control switch to the Off position. Move either motion-control lever to the center, unlocked position. Try starting the engine; the engine should not crank. Repeat with the other motion-control lever.
    Graphic
    G451952
  3. Sit on the seat, move the blade-control switch to the Off position, and move the motion-control levers to the Park position. Start the engine. While the engine is running, engage the blade-control switch, and rise slightly from the seat; the engine should shut off within 1 second.
    Graphic
    G451951
  4. Sit on the seat, move the blade-control switch to the Off position, and move the motion-control levers to the Park position. Start the engine. While the engine is running, move the motion-control levers to the center, unlocked position and rise slightly from the seat; the engine should shut off within 1 second.
    Graphic
    G451950
Positioning the Seat
Graphic
G451798
Adjusting the Motion-Control Lever Height
Adjust the motion-control levers higher or lower for your comfort.
Graphic
G450938
Adjusting the Motion-Control Lever Tilt
Adjust the motion-control levers forward or rearward for your comfort.
    Graphic
    G439363
  1. Loosen the knob.
  2. Pivot the control lever forward or rearward.
  3. Tighten the knob.
  4. Repeat the adjustment for the other control lever.
Converting to Side Discharge
Converting to Side Discharge for 122 cm (48-inch) Mower Decks
Install the fasteners into the same holes in the deck from where they were originally removed. This ensures that no holes remain open when operating the mower deck.
Warning
Open holes in the machine expose you and others to thrown debris that can cause severe injury.
  • Never operate the machine without hardware mounted in all holes in the machine housing.
  • Install the hardware in the mounting holes when you remove the mulching baffle.
 
  1. Park the machine on a level surface, disengage the blade-control switch, and move the motion-control levers outward to the Park position.
  2. Shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position.
  3. Remove the mower deck; refer to Removing the Mower Deck.
  4. Remove the left baffle as shown; retain the nuts.
    Graphic
    G482536
    1.  Nut5/16 inch (3)
    2.  Carriage bolt5/16 x 3/4 inch
  5. Use the 3 retained nuts and 3 bolts from the loose parts bag to plug the open holes to prevent flying debris.
    Note: Install the fasteners so that the nuts are outside the deck.
  6. Remove the fasteners securing the right baffle and baffle guard to the right side of the mower deck; retain the nuts and 1 carriage bolt.
    Note: The deflector is not shown for clarity.
    Graphic
    G482537
    1.  Nut5/16 inch (2)
    2.  Carriage bolt5/16 x 3/4 inch (2)
    3.  Square hole
  7. Remove the right baffle as shown; retain the nuts.
    Graphic
    G453334
    1.  Nut5/16 inch (2)
  8. Install the retained carriage bolt and a retained nut in the square hole shown in Step .
  9. Use the remaining 3 retained nuts and 3 bolts from the loose parts bag to plug the remaining open holes.
    Note: Install the fasteners so that the nuts are outside the deck.
  10. Locate the cutoff baffle in the loose parts bag.
  11. Remove the existing fasteners as shown and use them to install the cutoff baffle.
    Graphic
    G453337
    1.  Existing carriage bolt5/16 x 1 inch (2)
    2.  Existing nut5/16 inch (2)
  12. Install the mower deck; refer to Installing the Mower Deck.
Converting to Side Discharge for 137 cm (54-inch) Mower Decks
Install the fasteners into the same holes in the deck from where they were originally removed. This ensures that no holes remain open when operating the mower deck.
Warning
Open holes in the machine expose you and others to thrown debris that can cause severe injury.
  • Never operate the machine without hardware mounted in all holes in the machine housing.
  • Install the hardware in the mounting holes when you remove the mulching baffle.
 
  1. Park the machine on a level surface, disengage the blade-control switch, and move the motion-control levers outward to the Park position.
  2. Shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position.
  3. Remove the mower deck; refer to Removing the Mower Deck.
  4. Remove the left baffle as shown; retain the nuts.
    Graphic
    G483204
    1.  Nut5/16 inch (4)
    2.  Carriage bolt5/16 x 3/4 inch
  5. Use the 4 retained nuts and 4 bolts from the loose parts bag to plug the open holes to prevent flying debris.
    Note: Install the fasteners so that the nuts are outside the deck.
  6. Remove the baffle guard as shown.
    Graphic
    G453358
    1.  Nut5/16 inch (2)
    2.  Carriage bolt5/16 x 3/4 inch (2)
  7. Install the baffle fasteners into the open holes.
  8. Remove the fasteners securing the right baffle to the right side of the mower deck; retain the nuts.
    Note: The deflector is not shown for clarity.
    Graphic
    G453362
    1.  Nut5/16 inch (2)
    2.  Carriage bolt5/16 x 3/4 inch (2)
  9. Remove the right baffle as shown; retain the nuts.
    Graphic
    G453361
    1.  Nut5/16 inch (2)
  10. Use the 4 retained nuts and 4 bolts from the loose parts bag to plug the open holes.
    Note: Install the fasteners so that the nuts are outside the deck.
  11. Locate the cutoff baffle in the loose parts bag.
  12. Remove the existing fasteners shown and use them to install the cutoff baffle.
    Graphic
    G453359
    1.  Existing carriage bolt5/16 x 1 inch (2)
    2.  Existing nut5/16 inch (2)
  13. Install the mower deck; refer to Installing the Mower Deck.
Converting to Side Discharge for 152 cm (60-inch) Mower Decks
Install the fasteners into the same holes in the deck from where they were originally removed. This ensures that no holes remain open when operating the mower deck.
Warning
Open holes in the machine expose you and others to thrown debris that can cause severe injury.
  • Never operate the machine without hardware mounted in all holes in the machine housing.
  • Install the hardware in the mounting holes when you remove the mulching baffle.
 
  1. Park the machine on a level surface, disengage the blade-control switch, and move the motion-control levers outward to the Park position.
  2. Shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position.
  3. Remove the mower deck; refer to Removing the Mower Deck.
  4. Remove the left baffle as shown; retain the nuts.
    Graphic
    G483240
    1.  Nut5/16 inch (3)
    2.  Carriage bolt5/16 x 3/4 inch (1)
  5. Use the 4 retained nuts and 4 bolts from the loose parts bag to plug the open holes to prevent flying debris.
    Note: Install the fasteners so that the nuts are outside the deck.
  6. Remove the fasteners securing the right baffle and baffle guard to the right side of the mower deck; retain the nuts and 1 carriage bolt.
    Note: The deflector is not shown for clarity.
    Graphic
    G483241
    1.  Nut5/16 inch (2)
    2.  Spacer
    3.  Carriage bolt5/16 x 3/4 inch (2)
    4.  Square hole
  7. Remove the right baffle as shown; retain the nuts.
    Graphic
    G454148
    1.  Nut5/16 inch (3)
  8. Install the retained carriage bolt and a retained nut in the square hole shown in Step .
  9. Use the remaining 4 retained nuts and 4 bolts from the loose parts bag to plug the remaining open holes.
    Note: Install the fasteners so that the nuts are outside the deck.
  10. Locate the cutoff baffle in the loose parts bag.
  11. Remove the existing fasteners as shown and use them to install the cutoff baffle.
    Graphic
    G454146
    1.  Existing carriage bolt5/16 x 1 inch (2)
    2.  Existing nut5/16 inch (2)
  12. Install the mower deck; refer to Installing the Mower Deck.

During Operation

During Operation Safety
  • The owner/operator can prevent and is responsible for accidents that may cause personal injury or property damage.
  • Use your full attention while operating the machine. Do not engage in any activity that causes distractions; otherwise, injury or property damage may occur.
  • Do not operate the machine while ill, tired, or under the influence of alcohol or drugs.
  • Do not operate the machine unless all guards and safety devices, such as the deflectors and the entire grass catcher, are in place and functioning properly. Replace worn or deteriorated parts with genuine Toro parts when necessary.
  • Operating engine parts, especially the muffler, can become extremely hot. Severe burns can occur on contact and debris, such as leaves, grass, brush, etc. can catch fire. Keep the engine area free from debris and excessive oil and grease.
  • Operate the engine only in well-ventilated areas. Exhaust gases contain carbon monoxide, which is lethal if inhaled.
  • Operate the machine only in good visibility and appropriate weather conditions. Do not operate the machine when there is the risk of lightning.
  • Start the engine with your feet well away from the blades.
  • Keep your hands and feet away from moving parts. Keep clear of the discharge opening.
  • Keep away from holes, ruts, bumps, rocks, and other hazards. Use care when approaching blind corners, shrubs, trees, tall grass or other objects that may hide obstacles or obscure your view.
  • Do not mow with the discharge deflector raised, removed, or altered unless there is a grass-collection system or mulch kit in place and working properly.
  • Do not mow in reverse unless it is absolutely necessary. Always look down and behind you before moving the machine in reverse.
  • Stop the blades whenever you are not mowing. Slow down the machine, and use caution when crossing surfaces other than grass or when transporting the machine to and from the operating area.
  • Be aware of the mower discharge path and direct the discharge away from others. Avoid discharging material against a wall or obstruction because the material may ricochet back toward you.
  • If the machine strikes an object or starts to vibrate, immediately shut off the engine, remove the key, and wait for all moving parts to stop before examining the machine for damage. Make all necessary repairs before resuming operation.
  • Slow down and use caution when making turns and crossing roads and sidewalks with the machine. Always yield the right-of-way.
  • Never leave a running machine unattended.
  • Before you leave the operating position, do the following:
    • Park the machine on a level surface.
    • Disengage the power takeoff and lower the attachments.
    • Engage the parking brake.
    • Shut off the engine and remove the key.
    • Wait for all moving parts to stop.
  • Never carry children on the machine.
  • Do not carry children on the machine, even when the blades are not moving. Children could fall off and be seriously injured or prevent you from safely operating the machine. Children who have been given rides in the past could appear in the operating area without warning and be run over or backed over by the machine.
  • Children are often attracted to the machine and the mowing activity. Never assume that children will remain where you last saw them.
  • Keep children out of the operating area and under the watchful care of a responsible adult other than the operator.
  • Be alert and shut off the machine if children enter the operating area.
  • Before backing up or turning the machine, look down and all around for small children.
  • Do not use the machine as a towing vehicle unless it has a hitch installed. Attach towed equipment to the machine only at the hitch point.
  • Use only accessories and attachments approved by The Toro® Company.
Slope Safety
  • Slopes are a major factor related to loss of control and rollover accidents, which can result in severe injury or death. The operator is responsible for safe slope operation. Operating the machine on any slope requires extra caution. Before using the machine on a slope, do the following:
    • Review and understand the slope instructions in the manual and on the machine.
    • Use an angle indicator to determine the approximate slope angle of the area.
    • Never operate on slopes greater than 15°.
    • Evaluate the site conditions of the day to determine if the slope is safe for machine operation. Use common sense and good judgment when performing this evaluation. Changes in the terrain, such as moisture, can quickly affect the operation of the machine on a slope.
  • Identify hazards at the base of the slope. Do not operate the machine near drop-offs, ditches, embankments, water, or other hazards. The machine could suddenly roll over if a wheel goes over the edge or the edge collapses. Keep a safe distance (twice the width of the machine) between the machine and any hazard. Use a walk-behind machine or a hand trimmer to mow the grass in these areas.
    Graphic
    G229111s
    1.  Safe Zoneuse the machine here on slopes less than 15° or flat areas.
    2.  Danger Zoneuse a walk-behind mower and/or a hand trimmer on slopes greater than 15° and near drop-offs or water.
    3.  Water
    4.  W = Width of the machine
    5.  Keep a safe distance (twice the width of the machine) between the machine and any hazard.
  • Avoid starting, stopping, or turning the machine on slopes. Avoid making sudden changes in speed or direction; turn slowly and gradually.
  • Do not operate a machine under any conditions where traction, steering, or stability is in question. Be aware that operating the machine on wet grass, across slopes, or downhill may cause the machine to lose traction. Loss of traction to the drive wheels may result in sliding and a loss of braking and steering. The machine can slide even if the drive wheels are stopped.
  • Remove or mark obstacles such as ditches, holes, ruts, bumps, rocks, or other hidden hazards. Tall grass can hide obstacles. Uneven terrain could overturn the machine.
  • Use extra care while operating with accessories or attachments, such as grass-collection systems. These can change the stability of the machine and cause a loss of control. Follow directions for counterweights.
  • If possible, keep the deck lowered to the ground while operating on slopes. Raising the deck while operating on slopes can cause the machine to become unstable.
Towing Safety
  • Do not attach towed equipment except at the hitch point.
  • Do not use the machine as a towing vehicle unless it has a hitch installed.
  • Do not exceed the maximum gross towing weight.
  • Never allow children or others near the towed equipment.
  • On slopes, the weight of the towed equipment may cause loss of traction, increased risk of rollover, and loss of control. Reduce the towed weight and slow down.
  • The stopping distance may increase with the weight of a towed load. Travel slowly and allow extra distance to stop.
  • Make wide turns to keep the attachment clear of the machine.
Entering the Operators Position
  1. Use the mower deck as a step to get into the operators position.
    Graphic
    G453429
Starting the Engine
  1. Start the engine as shown.
    Note: A warm or hot engine may not require choking.
    Important
    Do not engage the starter for more than 5 seconds at a time, otherwise you can damage the starter motor. If the engine fails to start, wait 10 seconds before operating the engine starter again.
     
    Graphic
    G451068
Shutting Off the Engine
    Graphic
    G440082
  1. Disengage the blades by moving the blade-control switch to the Off position.
  2. Move the motion-control levers outward to the Park position.
  3. Move the throttle control between the half and full throttle position.
  4. Turn the key to the Off position and remove the key.
    Caution
    Children or bystanders may be injured if they move or attempt to operate the machine while it is unattended.
    Always remove the key and engage the parking brake when leaving the machine unattended.
     
Driving the Machine
Caution
Positioning one lever too far in front of the other causes the machine to spin very rapidly. As a result, you may lose control of the machine, causing personal injury to you and damage to the machine.
Slow down the machine before making sharp turns.
 
The drive wheels turn independently, powered by motors on each axle. You can turn 1 side in reverse while you turn the other forward, causing the machine to spin rather than turn. This greatly improves the machine maneuverability but may require some time for you to adapt to how it moves.
  1. Move the motion-control levers down to the center, unlocked position.
    Graphic
    G426843s
    1.  Motion-control leversPark position
    2.  Center, unlocked position
    3.  Forward
    4.  Reverse
    5.  Front of the machine
  2. Graphic
    G397314s
  3. Slowly push the motion-control levers forward or rearward. Move 1 lever farther than the other lever to turn.
    Note: The farther you move the motion-control levers, the faster the machine moves in that direction.
  4. To stop, pull the motion-control levers back to the Neutral position.
Operating the Mower Blade-Control Switch (PTO)
Danger
The rotating blades under the mower deck are dangerous. Blade contact will cause serious injury or death.
Do not put your hands or feet under the mower or mower deck when the blades are engaged.
 
Danger
An uncovered discharge opening allows objects to be thrown toward you or bystanders. Also, contact with the blade could occur. Thrown objects or blade contact will cause serious injury or death.
Do not operate the mower with the discharge deflector raised, removed, or altered unless a grass collection system or mulch kit is in place and working properly.
 
  1. Move the throttle control to the Fast position.
  2. Engage the blade-control switch.
    Graphic
    G450387
  3. Mow as desired.
  4. Disengage the blade-control switch.
    Graphic
    G450388
Side Discharge
The hinged grass deflector disperses clippings to the side and down toward the turf.
Danger
Without the grass deflector, discharge cover, or complete grass catcher assembly mounted in place, you and bystanders are exposed to blade contact and thrown debris. Contact with rotating mower blade(s) and thrown debris will cause injury or death.
  • Do not remove the grass deflector from the machine, because the grass deflector routes material down toward the turf. If the grass deflector is ever damaged, replace it immediately.
  • Never put your hands or feet under the mower.
  • Never try to clear the discharge area or mower blades unless the power takeoff (PTO) is off. Rotate the key to the Off position and remove the key.
 
Adjusting the Height of Cut
You can adjust the height of cut from 38 to 127 mm (1-1/2 to 5 inches) in 6.4 mm (1/4 inch) increments.
    Graphic
    G455680
  1. Push the deck-lift pedal with your foot to raise the mower deck.
  2. Remove the pin from the height-of-cut bracket.
  3. Insert the pin into the hole corresponding to the desired height of cut .
  4. Lower the deck slowly until the lever contacts the pin.
Using the Transport Lock
    Graphic
    G456097
  1. Push the deck-lift pedal fully forward to lock the mower deck in the Transport position.
  2. Push the deck-lift pedal fully forward and push the transport lock lever forward to the Unlock position, then slowly lower the mower deck to the desired height of cut.
Adjusting the Anti-Scalp Rollers
Whenever you change the height of cut, adjust the height of the anti-scalp rollers.
  1. Park the machine on a level surface, disengage the blade-control switch, and move the motion-control levers outward to the Park position.
  2. Shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position.
  3. Adjust the anti-scalp rollers to match the closest height-of-cut position.
    Note: Adjust the anti-scalp rollers so that the rollers do not touch the ground in normal, flat mowing areas.
    Graphic
    G454155
Operating Tips
Maximize Air Circulation
For best mowing and maximum air circulation, operate the engine at the Fast position. Air circulation is required to thoroughly cut grass clippings, so do not set the height-of-cut so low as to totally surround the mower deck in uncut grass. Always try to have 1 side of the mower deck free from uncut grass, which allows air to be drawn into the mower deck.
Avoid Cutting Too Low
When mowing uneven ground, raise the cutting height to slightly higher than normal to avoid scalping the turf. However, the cutting height used in the past is generally the best one to use. When cutting grass longer than 15 cm (6 inches) tall, you may want to cut the lawn twice to ensure an acceptable quality of cut.
Cut a Third of the Grass Blade
It is best to cut only about a third of the grass blade. Cutting more than that is not recommended unless grass is sparse, or it is late fall when grass grows more slowly.
Alternate the Mowing Direction
Alternate the mowing direction to keep the grass standing straight. This also helps disperse clippings, which enhances decomposition and fertilization.
Mowing Frequency
Grass grows at different rates at different times of the year. To maintain the same cutting height, mow more often in early spring. As the grass growth rate slows in mid summer, mow less frequently. If you cannot mow for an extended period, first mow at a high cutting height, then mow again 2 days later at a lower height setting.
Mow at Slower Ground Speeds
In certain conditions, mowing at a slower ground speed can improve cut quality.
Avoid Grass Clumps
If you must stop driving forward while mowing, a clump of grass clippings may drop onto your lawn. To avoid this, move onto a previously cut area with the blades engaged or disengage the mower deck while moving forward.
Keep the Underside of the Mower Deck Clean
Clean clippings and dirt from the underside of the mower deck after each use. Grass and dirt build-up will eventually decrease the cutting quality.
Maintain the Blades
Maintain a sharp blade throughout the cutting season because a sharp blade cuts cleanly without tearing or shredding the grass blades. Tearing and shredding turns grass brown at the edges, which slows growth and increases the chance of disease. Check the mower blades after each use for sharpness, and for any wear or damage. File down any nicks and sharpen the blades as necessary. If a blade is damaged or worn, replace it.

After Operation

After Operation Safety
  • Park the machine on a level surface, disengage the drives, engage the parking brake, shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operators position.
  • Wait for the machine to cool before servicing, adjusting, fueling, cleaning, or storing it.
  • Clean grass, leaves, excessive grease and oil, and other debris from the mower deck, muffler, drives, grass catcher, and engine area to help prevent fires.
  • Close the fuel-shutoff valve (if equipped) before storing or transporting the machine.
  • Use full-width ramps for loading the machine into a trailer or truck.
  • Tie the machine down securely using straps, chains, cable, or ropes. Both front and rear straps should be directed down and outward from the machine.
Cleaning the Machine
Clean the machine after each use.
  1. Park the machine on a level surface, disengage the blade-control switch, and move the motion-control levers outward to the Park position.
  2. Shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position.
  3. Clean grass and debris from cutting unit, muffler, drives, grass catcher, and engine.
    Important  
    You can wash the machine with a mild detergent and water. Do not pressure wash the machine. Avoid excessive use of water, especially near the control panel, under the seat, around the engine, hydraulic pumps, and motors.
     
Hauling the Machine
Use a heavy-duty trailer or truck to haul the machine. Use a full-width ramp. Ensure that the trailer or truck has all the necessary brakes, lighting, and marking as required by law. Please carefully read all the safety instructions. Knowing this information could help you or bystanders avoid injury. Refer to your local ordinances for trailer and tie-down requirements.
Warning
Driving on the street or roadway without turn signals, lights, reflective markings, or a slow-moving-vehicle emblem is dangerous and can lead to accidents causing personal injury.
Do not drive the machine on a public street or roadway.
 
Trailer Requirements
Warning
Loading a machine onto a trailer or truck increases the possibility of tip-over and could cause serious injury or death.
  • Use only a full-width ramp; do not use individual ramps for each side of the machine.
  • Do not exceed a 15-degree angle between the ramp and the ground or between the ramp and the trailer or truck.
  • Ensure that the length of ramp is at least 4 times as long as the height of the trailer or truck bed to the ground.
 
Graphic
G027996s
  1.  Full-width ramp(s) in stowed position
  2.  Side view of full-width ramp in loading position
  3.  Not greater than 15 degrees
  4.  Ramp is at least 4 times as long as the height of the trailer or truck bed to the ground
  5.  H = height of the trailer or truck bed to the ground
  6.  Trailer
Loading the Machine
Warning
Loading a machine onto a trailer or truck increases the possibility of tip-over and could cause serious injury or death.
  • Use extreme caution when operating a machine on a ramp.
  • Back the machine up the ramp and drive it forward down the ramp.
  • Avoid sudden acceleration or deceleration while driving the machine on a ramp as this could cause a loss of control or a tip-over situation.
 
  1. If using a trailer, connect it to the towing vehicle and connect the safety chains.
  2. If applicable, connect the trailer brakes.
  3. Lower the ramp, ensuring that the angle between the ramp and the ground does not exceed 15 degrees.
  4. Graphic
    G414592
  5. Back the machine up the ramp.
  6. Shut off the engine, remove the key, and move the motion-control levers outward to the Park position.
  7. Graphic
    G451313
  8. Tie down the machine using straps, chains, cable, or ropes. Refer to local regulations for tie-down requirements.
Unloading the Machine
    Graphic
    G414593
  1. Lower the ramp, ensuring that the angle between the ramp and the ground does not exceed 15 degrees.
  2. Drive the machine forward down the ramp.
 
 
 
Maintenance
 

Maintenance Safety

Recommended Maintenance Schedule
Maintenance
Service Interval
Maintenance Procedure
After the first 50 hours
Check the lug-nut torque.
Before each use or daily
Check the safety-interlock system.
Check the engine-oil level.
Inspect the blades.
Inspect the grass deflector for damage.
After each use
Clean grass and debris from the machine.
Clean the mower-deck housing.
Every 25 hours
Grease the caster wheel bearings (more often in sandy soil conditions).
Clean the air-cleaner foam element (more often in dusty, dirty conditions).
Check the tire pressure.
Check the belts for wear or cracks.
Every 50 hours
Replace the foam air-cleaner element (more often in dirty or dusty conditions).
Every 100 hours
Remove and clean the blower housing and any other cooling shrouds (more often in dirty or dusty conditions).
Replace the in-line fuel filter.
Every 100 hours or yearly, whichever comes first
Replace the paper air-cleaner element (more often in dirty or dusty conditions).
Change the engine oil and oil filter (more often in dirty or dusty conditions).
Check the spark plug(s).
Every 500 hours
Change the spark plug(s).
Yearly
Check the lug-nut torque.
Before storage
Charge the battery and disconnect the battery cables.
Perform all maintenance procedures listed above before storage.
Paint any chipped surfaces.
Important  
Refer to your engine owner's manual for additional maintenance procedures.
 

Pre-Maintenance Procedures

Moving a Non-Functioning Machine
  1. Park the machine on a level surface, disengage the blade-control switch, and move the motion-control levers outward to the Park position.
  2. Shut off the engine and wait for all moving parts to stop before leaving the operating position.
  3. Locate the bypass levers on the frame on both sides of the engine.
    Graphic
    G453452
  4. Move both bypass levers forward through the slotted hole and over to lock them in place .
    Warning
    Contact with hot surfaces may cause personal injury.
    Keep your hands, feet, face, clothing and other body parts away the engine, muffler and other hot surfaces.
     
    Warning
    The machine could unintentionally move while the bypass levers are locked forward in the slot and injure you or bystanders.
    Lock the bypass levers rearward after moving the machine.
     
  5. Disengage the parking brake by moving both motion-control levers down to the center, unlocked position.
    Note: Do not start the machine.
  6. Move the machine as required.
    Important  
    Always push the machine by hand. Do not tow the machine, because towing may damage it.
     
  7. Move the motion-control levers outward to the Park position.
  8. Move both bypass levers rearward and over through the slotted hole to lock them in place .
Releasing the Mower-Deck Curtain
  1. Loosen the 2 bottom bolts of the curtain to access the top of the mower deck.
    Important  
    Always tighten the bolts to connect the curtain after maintenance.
     
    Graphic
    G453430

Engine Maintenance

Engine Safety
  • Keep your hands, feet, face, other body parts, and clothing away from the muffler and other hot surfaces. Wait for the engine to cool before performing maintenance.
  • Do not change the engine governor speed or overspeed the engine.
Air Cleaner Service
Removing the Air-Cleaner Elements
  1. Park the machine on a level surface, disengage the blade-control switch, and move the motion-control levers outward to the Park position.
  2. Shut off the engine and wait for all moving parts to stop before leaving the operating position.
  3. Graphic
    G453476
  4. Clean around the air-cleaner cover to prevent dirt from getting into the engine and causing damage.
  5. Rotate the latches outward and remove the cover.
  6. Remove the air-cleaner elements .
  7. Graphic
    G453475
  8. Separate the foam and paper elements.
Servicing the Foam Element
  1. Wash the foam element in liquid soap and warm water. When the element is clean, rinse it thoroughly.
  2. Dry the element by squeezing it in a clean cloth.
    Important  
    Replace the foam element if it is torn of worn.
     
  3. Lightly oil the foam element using new engine oil and squeeze out any excess oil.
Servicing the Paper Air-Cleaner Element
  1. Clean the paper element by tapping it gently to remove dust.
    Note: If it is very dirty, replace the paper element with a new one.
  2. Inspect the element for tears, an oily film, or damage to the rubber seal.
  3. Replace the paper element if it is damaged.
    Important  
    Do not clean the paper filter.
     
Installing the Air Cleaner Elements
    Graphic
    G453478
  1. Install the foam pre-cleaner element over the paper element.
    Note: Ensure that you do not damage the elements.
  2. Graphic
    G453477
  3. Install the air-cleaner elements onto the air-cleaner base.
  4. Install the cover and secure it with the latches .
Engine-Oil Service
Engine-Oil Specifications
Oil Type
Detergent oil (including synthetic) of API service SJ or higher
Crankcase Capacity
1.9 L (64 fl oz) with oil filter
Viscosity
See the table below
Image
Checking the Engine-Oil Level
  1. Park the machine on a level surface, disengage the blade-control switch, and move the motion-control levers outward to the Park position.
  2. Shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position.
  3. Wait for the engine to cool so that the oil has had time to drain into the sump.
  4. To keep dirt, grass clippings, etc., out of the engine, clean the area around the oil-fill cap and dipstick before removing it.
  5. Check the engine-oil level as shown.
    Graphic
    G454028
    Important  
    If you overfill or underfill the engine crankcase with oil and run the engine, you may damage the engine.
     
Changing the Engine Oil and Oil Filter
  1. Park the machine on a level surface to ensure that the oil drains completely.
  2. Disengage the blade-control switch, and move the motion-control levers outward to the Park position.
  3. Shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position.
  4. Drain the oil from the engine.
    Graphic
    G225280s
  5. Change the engine-oil filter.
    Note: Ensure that the oil-filter gasket touches the engine and then turn the filter an extra 3/4 turn.
    Graphic
    G027477s
  6. Slowly pour approximately 80% of the specified oil into the filler tube and slowly add the additional oil to bring it to the Full mark.
    Graphic
    G365790s
  7. Dispose of the used oil at a recycling center.
Servicing the Spark Plug
Ensure that the air gap between the center and side electrodes is correct before installing the spark plug. Use a spark plug wrench for removing and installing the spark plug and a gapping tool or feeler gauge to check and adjust the air gap. Install a new spark plug if necessary.
Type: Champion® XC12YC
Air gap: 0.76 mm (0.03 inch)
Removing the Spark Plug
  1. Park the machine on a level surface, disengage the blade-control switch, and move the motion-control levers outward to the Park position.
  2. Shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position.
  3. Clean the area around the base of the plug to keep dirt and debris out of the engine.
  4. Remove the spark plug.
    Graphic
    G437139
Checking the Spark Plug
Important  
Do not clean the spark plug(s). Always replace the spark plug(s) when it has a black coating, worn electrodes, an oily film, or cracks.
 
If you see light brown or gray on the insulator, the engine is operating properly. A black coating on the insulator usually means the air cleaner is dirty.
  1. Set the gap to 0.75 mm (0.03 inch).
    Graphic
    G437150
Installing the Spark Plug
Graphic
G455874
Cleaning the Blower Housing
  1. To ensure proper cooling, clean the grass screen, cooling fins, and other external surfaces of the engine. Make sure that the cooling shrouds are installed. Torque the blower housing screws to 4.0 Nm (35 in-lb).
    Important  
    Operating the engine with a blocked grass screen, dirty or plugged cooling fins, and/or cooling shrouds removed causes engine damage due to overheating.
     

Fuel Maintenance

Danger
In certain conditions, fuel is extremely flammable and highly explosive. A fire or explosion from fuel can burn you and others and can damage property.
Refer to Fuel Safety for a complete list of fuel related precautions.
 
Replacing the Fuel Filter
  1. Park the machine on a level surface, disengage the blade-control switch, and move the motion-control levers outward to the Park position.
  2. Shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position.
  3. Clamp the fuel lines on both sides of the fuel filter.
  4. Replace the filter.
    Note: Ensure that the flow-direction arrow on the replacement filter points toward the engine.
    Important
    Never install a dirty filter after removing it from the fuel line.
     
    Graphic
    G453516
  5. Remove the clamps blocking the fuel flow.

Electrical System Maintenance

Electrical System Safety
  • Disconnect the cable from the negative terminal of the battery before repairing the machine.
  • Charge the battery in an open, well-ventilated area, away from sparks and flames. Unplug the charger before connecting or disconnecting the battery. Wear protective clothing and use insulated tools.
Battery Service
Removing the Battery
Warning
Battery terminals or metal tools could short against metal machine components, causing sparks. Sparks can cause the battery gasses to explode, resulting in personal injury.
  • When removing or installing the battery, do not allow the battery terminals to touch any metal parts of the machine.
  • Do not allow metal tools to short between the battery terminals and metal parts of the machine.
 
  1. Park the machine on a level surface, disengage the blade-control switch, and move the motion-control levers outward to the Park position.
  2. Shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position.
  3. Disconnect the negative (black) ground cable from the battery post.
    Note: Retain all fasteners.
    Warning
    Incorrectly removing the cables from battery could damage the machine and cables, causing sparks. Sparks can cause the battery gasses to explode, resulting in personal injury.
    • Always disconnect the negative (black) battery cable before disconnecting the positive (red) cable.
    • Always connect the positive (red) battery cable before connecting the negative (black) cable.
     
  4. Slide the rubber cover off the positive (red) cable.
  5. Disconnect the positive (red) cable from the battery post (+).
    Note: Retain all fasteners.
  6. Remove the battery hold-down and lift the battery from the battery tray.
    Graphic
    G440221
    1. Battery
    2. Terminal boot
    3. Negative () battery post
    4. Wing nut, washer, and bolt
    5. Battery hold-down
    6. Bolt, washer, and nut
    7. Positive (+) battery post
Charging the Battery
Warning
Charging the battery produces gasses that can explode.
Never smoke near the battery and keep sparks and flames away from battery.
 
Important
Always keep the battery fully charged. This is especially important to prevent battery damage when the temperature is below 0°C (32°F).
 
  1. Remove the battery from the machine.
  2. Charge the battery per the battery charger manufacturers instructions.
    Important  
    Do not overcharge the battery; otherwise, you could damage it.
     
    Graphic
    G003792S
    1.  Positive battery post
    2.  Negative battery post
    3.  Red (+) charger lead
    4.  Black (-) charger lead
  3. When the battery is fully charged, unplug the charger from the electrical outlet (if applicable), then disconnect the charger leads from the battery posts.
Cleaning the Battery
Note: Keep the terminals and the entire battery case clean, because a dirty battery discharges slowly.
  1. Park the machine on a level surface, disengage the blade-control switch, and move the motion-control levers outward to the Park position.
  2. Shut off the engine and wait for all moving parts to stop before leaving the operating position.
  3. Remove the battery from the machine.
  4. Wash the entire case with a solution of baking soda and water.
  5. Rinse the battery with clear water.
  6. Coat the battery posts and cable connectors with Grafo 112X (skin-over) grease or petroleum jelly to prevent corrosion.
  7. Install the battery.
Installing the Battery
  1. Position the battery in the tray.
  2. Using the fasteners previously removed, install the positive (red) battery cable to the positive (+) battery terminal.
  3. Using the fasteners previously removed, install the negative battery cable to the negative (-) battery terminal.
  4. Slide the red terminal boot onto the positive (red) battery post.
  5. Secure the battery with the hold-down.
    Graphic
    G440221
    1. Battery
    2. Terminal boot
    3. Negative () battery post
    4. Wing nut, washer, and bolt
    5. Battery hold-down
    6. Bolt, washer, and nut
    7. Positive (+) battery post
Jump-Starting the Machine
Warning
Jump-starting the battery can produce gasses that can explode.
Do not smoke near the battery, and keep sparks and flames away from battery.
 
Danger
Jump-starting a weak battery that is cracked or frozen or has a low electrolyte level or an open/shorted battery cell can cause an explosion, resulting in serious personal injury.
Do not jump-start a weak battery if these conditions exist.
 
  1. Check and clean corrosion from the battery terminals before jump-starting. Ensure that the connections are tight.
    Caution
    Corrosion or loose connections can cause unwanted electrical voltage spikes at any time during the jump-starting procedure.
    Do not attempt to jump-start the machine with loose or corroded battery terminals, or damage to the engine may occur.
     
  2. Make sure that the booster battery is a good and fully charged lead-acid battery at 12.6 V or greater.
    Note: Use properly sized jumper cables with short lengths to reduce voltage drop between systems. Make sure that the cables are color coded or labeled for the correct polarity.
    Warning
    Batteries contain acid and produce explosive gases.
    • Shield your eyes and face from the batteries at all times.
    • Do not lean over the batteries.
     
    Note: Ensure that the vent caps are tight and level. Place a damp cloth, if available, over any vent caps on both batteries. Also ensure that the machines do not touch and that both electrical systems are off and at the same rated system voltage. These instructions are for negative ground systems only.
  3. Connect the positive (+) cable to the positive (+) terminal of the discharged battery that is wired to the starter or solenoid as shown:
    Graphic
    g012785
    1.  Positive (+) cable on discharged battery
    2.  Positive (+) cable on booster battery
    3.  Negative () cable on the booster battery
    4.  Negative () cable on the engine block
    5.  Booster battery
    6.  Discharged battery
    7.  Engine block
  4. Connect the other end of the positive (+) jumper cable to the positive terminal of the battery in the other machine.
  5. Connect an end of the negative (-) jumper cable to the negative post of the battery in the other machine.
  6. Connect the other end of the negative (-) jumper cable to a ground point, such as an unpainted bolt or chassis member.
  7. Start the engine in the other machine. Let it run a few minutes, then start your engine.
  8. Remove the cables in the reverse order of connection.
  9. Install the cover to the jump post.
Servicing the Fuses
The electrical system is protected by fuses. It requires no maintenance; however, if a fuse blows, check the component/circuit for a malfunction or short.
  1. Park the machine on a level surface, disengage the blade-control switch, and move the motion-control levers outward to the Park position.
  2. Shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position.
  3. Replace the blown fuse with a new fuse.
    Graphic
    G440132
    1.  Charge circuit (15 A)
    2.  Main (25 A)

Drive System Maintenance

Checking the Tire Pressure
Maintain the air pressure in the front and rear tires as specified. Uneven tire pressure can cause an uneven cut. Check the pressure at the valve stem when the tires are cold to get the most accurate pressure reading.
    Graphic
    G441539
  1. Inflate the front caster wheel tires to 103 kPa (15 psi) or the pressure indicated on the sidewall, whichever is lower.
  2. Inflate the rear drive-wheel tires to 90 kPa (13 psi).
Checking the Wheel Lug Nuts
  1. Check and torque the wheel lug nuts to 108 Nm (80 ft-lb).
Adjusting the Tracking
When driving the machine forward full speed across a flat, level surface, if the machine pulls to 1 side, adjust the tracking.
If the machine pulls to the left, adjust the right motion-control lever; if the machine pulls to the right, adjust the left motion-control lever.
Note: You can adjust the tracking only for driving forward.
  1. Park the machine on a level surface, disengage the blade-control switch, and move the motion-control levers outward to the Park position.
  2. Shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position.
  3. Locate the tracking-adjustment bolt near the motion-control lever on the particular side that needs adjusting.
    Graphic
    G453528
  4. Rotate the bolt to decrease the speed for that particular wheel.
    Note: Rotate the bolt a small amount to make minor adjustments.
  5. Start the machine and drive forward across a flat, level surface with the motion-control levers fully forward to check if the machine tracks straight. Repeat the procedure as needed.

Belt Maintenance

Inspecting the Belts
  1. Park the machine on a level surface, disengage the blade-control switch, and move the motion-control levers outward to the Park position.
  2. Shut off the engine and wait for all moving parts to stop before leaving the operating position.
  3. Set the height of cut at the lowest cutting position.
  4. Inspect the belt for wear. Replace the belt if it is worn.
    The signs of a worn belt include squealing while the belt is rotating; the blades slipping while cutting grass; and frayed edges, burn marks, and cracks on the belt.
Replacing the Mower Belt
The signs of a worn belt include squealing while the belt is rotating, blades slipping while cutting grass, and frayed edges, burn marks, and cracks on the belt. Replace the mower belt if any of these conditions are evident.
  1. Park the machine on a level surface, disengage the blade-control switch, and move the motion-control levers outward to the Park position.
  2. Shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position.
  3. Set the height of cut at the lowest cutting position.
  4. Release the mower-deck curtain.
  5. Remove the pulley covers.
    Graphic
    G453681
  6. Loosen the nut securing the wire form to the idler pulley.
    Graphic
    G453683
  7. Using a spring-removal too (Toro Part No. 92-5771), remove the idler spring from the deck hook to remove tension on the idler pulley.
    Warning
    The spring is under tension when installed and can cause personal injury.
    Be careful when removing the belt.
     
    Graphic
    G453682
    1.  Deck pulley
    2.  Mower belt
    3.  Engine pulley
    4.  Idler pulley
    5.  Spring
    6.  Spring-removal tool
  8. Roll the belt off the pulleys.
  9. Route the new belt around the engine pulley and mower pulleys.
  10. Use the spring-removal tool to install the idler spring over the deck hook and place tension on the idler pulley and the mower belt.
  11. Position the wire form against the idler arm as shown and tighten the nut.
    Graphic
    G453683
  12. Install the pulley covers.
  13. Tighten the bolts for the mower-deck curtain.

Mower-Deck Maintenance

Blade Safety
  • Inspect the blades periodically for wear or damage.
  • Use care when checking the blades. Wrap the blade(s) or wear gloves and use caution when servicing them. Only replace damaged blades; never straighten or weld them.
  • On multi-bladed machines, take care as rotating one blade can cause other blades to rotate.
  • Replace worn or damaged blades and bolts in sets to preserve balance.
Blade Service
To ensure a superior quality of cut, keep the blades sharp. For convenient sharpening and replacement, keep extra blades on hand.
Replace the blades if they hit a solid object, or if the blade is out of balance or bent.
Before Inspecting or Servicing the Blades
  1. Park the machine on a level surface, disengage the blade-control switch, and move the motion-control levers outward to the Park position.
  2. Shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position.
  3. Disconnect the spark-plug wires from the spark plugs.
Checking for Bent Blades
The machine must be on a level surface for this procedure.
  1. Raise the mower deck to the highest height-of-cut position.
  2. While wearing thickly padded gloves, or other adequate hand protection, slowly rotate the blade into a position that allows you to measure the distance between the cutting edge and the level surface.
    Graphic
    G451424
  3. Measure from the tip of the blade to the level surface.
    Graphic
    G451422
    1.  Blade (in position for measuring)
    2.  Level surface
    3.  Measured distance between blade and the surface (A)
  4. Rotate the same blade 180 degrees so that the opposite blade edge is now in the same position.
    Graphic
    G451423
    1.  Blade edge previous measured
    2.  Opposite blade edge
  5. Measure from the tip of the blade to the level surface.
    Graphic
    G451422
    1.  Blade (in position for measuring)
    2.  Level surface
    3.  Measured distance between blade and the surface (B)
  6. If the difference between A and B is greater than 3 mm (1/8 inch), replace the blade.
    Note: If you replace the blade and the difference continues to exceed 3 mm (1/8 inch), the blade spindle could be bent. Contact an Authorized Service Dealer for service.
  7. Repeat this procedure each blade.
Removing the Blades
  1. Hold the blade end using a rag or thickly padded glove.
  2. Remove the blade as shown.
    Graphic
    G451425
Sharpening the Blades
    Graphic
    G000552s
  1. Use a file to sharpen the cutting edge at both ends of the blade. Ensure to maintain the original angle .
    Note: Remove the same amount of material from both cutting edges so that the blade retains its balance.
  2. Graphic
    G000553s
  3. Check the balance of the blade by putting it on a blade balancer .
    Note: If the blade stays in a horizontal position, the blade is balanced and can be used.
    If the blade is not balanced, file some metal off the end of the sail area only.
  4. Repeat this procedure until the blade is balanced.
Installing the Blades
Warning
Operating a machine after incorrectly installing the blade assembly and/or not using genuine Toro blade and blade hardware could allow a blade or blade component to be thrown out from under the deck, resulting in serious injury or death.
Always install genuine Toro blades and blade hardware according to the instructions.
 
    Graphic
    G451425
  1. Install the blade as shown.
    Note: The curved part of the blade must be pointing upward toward the inside of the mower to ensure proper cutting.
  2. Torque the blade bolt to 136 to 149 N·m (100 to 110 ft-lb).
Leveling the Mower Deck
Ensure that the mower deck is level any time you install the mower deck or when you see an uneven cut on your lawn.
Preparing to Level the Mower Deck
  1. Park the machine on a level surface, disengage the blade-control switch, and move the motion-control levers outward to the Park position.
  2. Shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position.
  3. Ensure that the tires are inflated to the correct specifications and the caster wheels are facing straight forward.
  4. Check the mower deck for bent blades; remove and replace any bent blades.
  5. Raise the mower deck to the 76 mm (3 inch) height-of-cut setting.
Checking the Mower-Deck Level
    Graphic
    G414698
  1. Position the blades side-to-side.
  2. Measure at locations and from a level surface to the cutting edge of the blade tips .
    The difference between the measurements should be no more than 5 mm (3/16 inch). If the measurement is larger, adjust the side-to-side level.
  3. Graphic
    G414700
  4. Position 1 blade front-to-rear.
  5. Measure at locations and from a level surface to the cutting edge of the blade tips .
    The front blade tip should be 1.6 to 7.9 mm (1/16 to 5/16 inch) lower than the rear blade tip. If the measurement is not correct, adjust the front-to-rear level.
Leveling the Mower Deck
  1. Set the anti-scalp rollers to the top holes or remove them completely for this procedure.
  2. Set the height-of-cut lever to the 76 mm (3 inch) position.
  3. Graphic
    G453680
  4. Place 2 blocks , each having a thickness of 6.6 cm (2-5/8 inches), under each side of the front edge of the deck.
    Important  
    Do not place the blocks under the anti-scalp roller brackets.
     
  5. Place 2 blocks , each having a thickness of 7.3 cm (2-7/8 inches), under each side of the rear edge of the deck.
  6. Graphic
    G456118
  7. Loosen the lower fasteners securing the brackets to all 4 corners of the deck and ensure that the mower deck sits securely on all 4 blocks.
  8. Remove any slack from the deck brackets and ensure that the deck-lift foot lever is pushed back against the stop.
  9. Tighten the fasteners.
  10. Ensure that the blocks fit snugly under the deck edge and that all attachment bolts are tight.
  11. Check the side-to-side level and front-to-rear level; repeat the procedure until the measurements are correct.
Removing the Mower Deck
  1. Park the machine on a level surface, disengage the blade-control switch, and move the motion-control levers outward to the Park position.
  2. Shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position.
  3. Lower the height-of-cut lever to the lowest position.
  4. Release the mower-deck curtain.
  5. Graphic
    G453722
  6. Remove the hairpin cotter and washer from the front support rod , and remove the rod from the deck bracket .
    Note: Retain all parts for future installation.
  7. Graphic
    G453704
  8. Remove the upper fasteners securing the brackets to all 4 lift arms.
  9. Slide the mower deck rearward to remove the mower belt from the engine pulley.
  10. Slide the mower deck out from underneath the machine.
Installing the Mower Deck
  1. Park the machine on a level surface, disengage the blade-control switch, and move the motion-control levers outward to the Park position.
  2. Shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position.
  3. Slide the mower deck under the machine.
  4. Lower the height-of-cut lever to the lowest position.
  5. Graphic
    G453704
  6. Install the lift links to the deck-lift arms using the previously removed fasteners.
  7. Graphic
    G453722
  8. Attach the front support rod to the deck bracket with the hairpin cotter and washer.
  9. Install the mower belt onto the engine pulley.
  10. Tighten the bolts for the mower-deck curtain.
Replacing the Grass Deflector
Danger
An uncovered discharge opening allows objects to be thrown toward you or bystanders. Also, contact with the blade could occur. Thrown objects or blade contact will cause serious injury or death.
Do not operate the mower with the discharge deflector raised, removed, or altered unless a grass collection system or mulch kit is in place and working properly.
 
  1. Park the machine on a level surface, disengage the blade-control switch, and move the motion-control levers outward to the Park position.
  2. Shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position.
  3. Disengage the spring from the notch in the deflector bracket and slide the rod out of the welded deck brackets, spring, and discharge deflector.
    Graphic
    G456086
    1.  Rod
    2.  Grass deflector
    3.  Spring
    4.  Deck brackets
    5.  Cotter pin
    6.  Spring installed over the rod
  4. Remove the damaged or worn grass deflector.
  5. Position the new discharge deflector with the bracket ends between the welded brackets on the deck as shown.
    Graphic
    G456085
    1.  Rod and spring assembly installed
    2.  Loop end of the spring installed into the notch of the deflector bracket
    3.  Rod, short end, moved behind the mower bracket
    4.  Short end, retained by mower bracket
    5.  Cotter pin
  6. Secure the rod and spring assembly by twisting it so that the short end of the rod is behind the front bracket welded to the deck.
  7. Install the cotter pin into the end of the rod.
    Important  
    The grass deflector must be spring-loaded in the down position. Lift the deflector up to test that it snaps into the full-down position.
     

Cleaning

Disposing of Waste
Engine oil, batteries, hydraulic fluid, and engine coolant are pollutants to the environment. Dispose of these according to your state and local regulations.
 
 
 
Storage
 

Storage Safety

Preparing the Machine for Storage Over 30 Days

  1. Park the machine on a level surface, disengage the blade-control switch, and move the motion-control levers outward to the Park position.
  2. Shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position.
  3. Clean the machine.
    Important  
    You can wash the machine with a mild detergent and water. Do not pressure-wash the machine. Avoid excessive use of water, especially near the drive system and engine. Pressure-washing can force dirt and water into critical parts, such as spindle bearings and electrical switches.
     
    1. Remove grass clippings, dirt, and grime from the external parts of the entire machine, especially the engine.
    2. Scrape any heavy buildup of grass and dirt from the underside of the mower, then wash the machine with a garden hose.
    3. Run the machine with the PTO switch engaged and the engine at high idle for 2 to 5 minutes after washing.
  4. Check the parking brake operation.
  5. Grease the machine.
  6. Check the tire pressure.
  7. Charge the battery.
  8. Check the condition of the cutting blades.
  9. Prepare the fuel system.
    1. Add a petroleum-based fuel stabilizer/conditioner to the fuel in the tank. Do not use an alcohol-based stabilizer (ethanol or methanol).
    2. Run the engine to distribute conditioned fuel through the fuel system for 5 minutes.
    3. Shut off the engine, allow it to cool, and drain the fuel tank using a pump-type syphon or operate the engine until it shuts off.
    4. Dispose of fuel properly. Recycle as per local codes.
      Important  
      Do not store fuel containing stabilizer/conditioner longer than the duration recommended by the fuel-stabilizer manufacturer.
       
  10. Prepare the engine.
    1. Service the air cleaner.
    2. Change the engine oil.
    3. Remove the spark plugs and pour 30 ml (2 tablespoons) of engine oil into the spark plug holes.
    4. Place a rag over the spark plug holes to catch any oil spray, then crank the engine and distribute the oil inside the cylinder.
    5. Install the spark plugs, but do not install the wires.
  11. Remove the battery or disconnect the negative (-) battery cable.
    Note: Store the battery in a cool, dry location, where it will not be exposed to extreme temperatures or water. Keep the battery fully charged, especially in temperatures below 0°C (32°F).
  12. Check and tighten all fasteners. Repair or replace any worn, damaged, or missing parts.
  13. Paint all scratched or bare metal surfaces with paint available from your Authorized Service Dealer.
  14. Store the machine in a clean, dry garage or storage area. Cover the machine to protect it and keep it clean.

Storing the Battery

Note: Follow the tips below to properly store the battery.
Battery Storage Tips
If you are storing the battery outside the machine, do the following:
  • Store the battery in a cool, dry area in an upright position.
  • Do not stack batteries directly on top of each other, unless they are in cartons.
  • Do not stack more than 3 batteries (only 2 if the battery type is commercial).
  • Test a wet battery every 4 to 6 months and charge it, if necessary.
  • Always test and charge the battery before installation.
 
 
 
Troubleshooting
 
The fuel tank is showing signs of collapsing or the machine is frequently showing signs of running out of fuel.
Possible Cause
Corrective Action
The air-cleaner paper element clogged.
  1. Clean the paper element.
The engine overheats.
Possible Cause
Corrective Action
The engine load is excessive.
  1. Reduce the ground speed.
The oil level in the crankcase is low.
  1. Add oil to the crankcase.
The cooling fins and air passages under the engine-blower housing are plugged.
  1. Remove the obstruction from the cooling fins and air passages.
The air cleaner is dirty.
  1. Clean or replace the air-cleaner element.
Dirt, water, or stale fuel is in the fuel system.
  1. Contact an Authorized Service Dealer.
The starter does not crank.
Possible Cause
Corrective Action
The blade-control switch is engaged.
  1. Disengage the blade-control switch.
The motion-control levers are not in the park position.
  1. Move the motion-control levers outward to the park position.
The battery is dead.
  1. Charge the battery.
The electrical connections are corroded or loose.
  1. Check the electrical connections for good contact.
A fuse is blown.
  1. Replace the fuse.
A relay or switch is damaged.
  1. Contact an Authorized Service Dealer.
The engine does not start, starts hard, or fails to keep running.
Possible Cause
Corrective Action
The fuel tank is empty.
  1. Fill the fuel tank.
The choke (if applicable) is not on.
  1. Move the choke lever to the on position.
The air cleaner is dirty.
  1. Clean or replace the air-cleaner element.
The spark-plug wire(s) is loose or disconnected.
  1. Install the wire(s) on the spark plug.
The spark plug(s) is pitted, fouled, or the gap is incorrect.
  1. Install a new, correctly gapped spark plug(s).
There is dirt in fuel filter.
  1. Replace the fuel filter.
Dirt, water, or stale fuel is in fuel system.
  1. Contact an Authorized Service Dealer.
There is incorrect fuel in the fuel tank.
  1. Drain the tank and replace the fuel with the proper type.
The oil level in the crankcase is low.
  1. Add oil to the crankcase.
The engine loses power.
Possible Cause
Corrective Action
The engine load is excessive.
  1. Reduce the ground speed.
The air cleaner is dirty.
  1. Clean the air-cleaner element.
The oil level in the crankcase is low.
  1. Add oil to the crankcase.
The cooling fins and air passages under the engine blower housing are plugged.
  1. Remove the obstruction from the cooling fins and air passages.
The spark plug(s) is pitted, fouled, or the gap is incorrect.
  1. Install a new, correctly gapped spark plug(s).
The fuel-tank vent is blocked.
  1. Contact an Authorized Service Dealer.
There is dirt in the fuel filter.
  1. Replace the fuel filter.
Dirt, water, or stale fuel is in the fuel system.
  1. Contact an Authorized Service Dealer.
There is incorrect fuel in the fuel tank.
  1. Contact an Authorized Service Dealer.
The machine does not drive.
Possible Cause
Corrective Action
The bypass valves are open.
  1. Close the tow valves.
The traction belts are worn, loose, or broken.
  1. Contact an Authorized Service Dealer.
The traction belts are off the pulleys.
  1. Contact an Authorized Service Dealer.
The transmission has failed.
  1. Contact an Authorized Service Dealer.
The machine vibrates abnormally.
Possible Cause
Corrective Action
The cutting blade(s) is/are bent or unbalanced.
  1. Install new cutting blade(s).
The blade mounting bolt is loose.
  1. Tighten the blade mounting bolt.
The engine mounting bolts are loose.
  1. Tighten the engine mounting bolts.
The engine pulley, idler pulley, or blade pulley is loose.
  1. Tighten the appropriate pulley.
The engine pulley is damaged.
  1. Contact an Authorized Service Dealer.
The blade spindle is bent.
  1. Contact an Authorized Service Dealer.
The motor mount is loose or worn.
  1. Contact an Authorized Service Dealer.
The cutting height is uneven.
Possible Cause
Corrective Action
The blade(s) is not sharp.
  1. Sharpen the blade(s).
A cutting blade(s) is/are bent.
  1. Install a new cutting blade(s).
The mower is not level.
  1. Level the mower from side-to-side and front-to-rear.
An anti-scalp roller (if applicable) is not set correctly.
  1. Adjust the anti-scalp wheel height.
The underside of the mower deck is dirty.
  1. Clean the underside of the mower deck.
The tire pressure is incorrect.
  1. Adjust the tire pressure.
A blade spindle is bent.
  1. Contact an Authorized Service Dealer.
The blades do not rotate.
Possible Cause
Corrective Action
The drive belt is worn, loose or broken.
  1. Install a new drive belt.
The drive belt is off of the pulley.
  1. Install the drive belt and check the adjusting shafts and belt guides for the correct position.
The power-takeoff (PTO) switch or PTO clutch is faulty.
  1. Contact an Authorized Service Dealer.
The mower belt is worn, loose, or broken.
  1. Install a new mower belt.
 
 
 
Schematics
 

Electrical Diagram

Graphic
G454156