Light Kit
Dingo® TX 1000 Turbo Compact Tool Carrier

Preparing the Machine

  1. Park the machine on a level surface.
  2. Engage the parking brake.
  3. Lower the loader arms.
  4. Shut off the engine and remove the key.
  5. Open the hood.
  6. Turn the battery-disconnect switch to the Off position.
  7. Remove the rear cover; refer to the Operator’s Manual for the machine.

Installing the Front Light

Parts Required
1
Light
1
Front bracket
1
Bolt (5/16 x 3/4 inch)
1
Nut (5/16 inch)
2
Carriage bolt (1/4 x 3/4 inch)
2
Nut (1/4 inch)
  1. Install the front bracket to the frame on the left side of the control panel.
    Graphic
    G504763
    1.  Nut—1/4 inch (2)
    2.  Carriage bolt—1/4 x 3/4 inch (2)
  2. Install a light to the front bracket.
    Graphic
    G504764
    1.  Nut—5/16 inch
    2.  Bolt—5/16 x 3/4 inch

Installing the Rear Light

Parts Required
1
Light
1
Rear bracket
1
Bolt (5/16 x 3/4 inch)
1
Nut (5/16 inch)
2
Bolt (1/4 x 3/4 inch)
2
Nut (1/4 inch)
  1. Install the rear bracket to the frame on the right side of the machine.
    Graphic
    G504789
    1.  Bolt—1/4 x 3/4 inch (2)
    2.  Nut—1/4 inch (2)
  2. Install a light to the rear bracket.
    Graphic
    G504790
    1.  Bolt—5/16 x 3/4 inch
    2.  Nut—5/16 inch

Routing the Wire Harness

Parts Required
1
Wire harness
1
Switch
4
Cable tie
Graphic
G341986s
  1. Front light
  2. Switch
  3. Machine harness connector
  4. Accessory connector
  5. Rear light
  1. Remove the 2 bolts securing the relay bracket to the frame.
    Note: This provides extra clearance to route the wire harness.
    Graphic
    G508745
  2. Remove the plug from the left side of the control panel. From inside the machine, behind the relay bracket, route the front light connector through the hole and connect it to the front light.
    Graphic
    G508746
  3. Remove the plug, route the switch connector through the hole, and connect it to the switch. Install the switch into the hole.
    Graphic
    G508748
  4. Route the rear light connector to the rear of the machine, under the hoses, to the right side of the machine, and connect it to the rear light.
    Graphic
    G508747
  5. Connect the accessory connector to the accessory port (P02) on the machine wire harness.
    Note: Use the accessory connector from the kit wire harness to connect any other powered accessories.
    Graphic
    G508744
  6. Use cable ties to secure the wire harness away from moving parts at the following locations:
    • Front reference bar
      Graphic
      G508957
    • Main wire harness, behind the air cleaner
      Note: Coil any excess slack in the wire harness when you secure it to the main wire harness.
      Graphic
      G508959
    • Rear light bracket
      Graphic
      G508960
    • Hydraulic hoses
      Important  
      Ensure that the wire harness is secured away from the radiator fan.
       
      Graphic
      G508958
  7. Use the 2 bolts previously removed to secure the relay bracket to the frame.
    Graphic
    G508745

Installing the Reflectors

Parts Required
2
Reflector
  1. Install the reflectors at the locations shown.
    Graphic
    G504820

Completing the Installation

  1. Install the rear cover.
  2. Turn the battery-disconnect switch to the On position.
  3. Close the hood.