Reelmaster® 3100-D Traction Unit
Disclaimers and Regulatory Information
Electromagnetic Compatibility Certification
Introduction
Manual Conventions
Safety Alert Classifications
Safety
During Operation Safety
Rollover Protection System (ROPS)
Safety
Safety and Instructional Decals
Setup
| 2 |
|
Installing the Steering
Wheel |
| 3 |
|
Charging and Connecting
the Battery |
| 4 |
|
Checking the Slope Indicator |
| 5 |
|
Installing the Roll Bar |
| 6 |
|
Installing the Front Lift
Arms |
| 7 |
|
Preparing to Install the
Lift Arms |
| 8 |
|
Assembling the Lift Arms
to the Machine |
| 9 |
|
Assembling the Lift Cylinder
to the Left Lift Arm |
| 10 |
|
Assembling the Lift Cylinder
to the Right Lift Arm |
| 11 |
|
Installing the Carrier
Frames to the Cutting Units
|
| 12 |
|
Preparing the Cutting Units |
| 13 |
|
Assembling the Carrier
Frames for the Front Cutting Units
|
| 14 |
|
Assembling the Cutting
Unit and Rear Carrier Frame
|
| 15 |
|
Assembling the Carrier
Frames for the Front Cutting Units
|
| 16 |
|
Assembling the Cutting
Unit and Rear Carrier Frame
|
| 17 |
|
Installing the Cutting
Units |
| 18 |
|
Installing the Cutting
Unit Drive Motors |
| 19 |
|
Installing the Telematics
Device |
| 20 |
|
Adjusting the Lift Arms |
| 21 |
|
Checking Lift Arm and Rear
Cutting Unit Clearance |
| 22 |
|
Adjusting Lift Arm Clearance |
| 23 |
|
Adjusting the Lift Arm
Stop Bolts |
| 24 |
|
Adjusting the Rear Cutting
Unit Clearance |
| 26 |
|
Installing the Hood Latch |
| 27 |
|
Installing the Exhaust
Guard |
| 28 |
|
Installing the CE Decals |
| 29 |
|
Applying the Year of Production
Decal and CE Decal |
| 30 |
|
Applying the CE Tilt Danger
Decal |
| 31 |
|
Installing the Tipper Roller
Kit (Optional) |
Product Overview
Controls
Cutting-Unit Drive Switch
Oil Pressure Warning Light
Engine Coolant Temperature Warning
Light
Glow-Plug Indicator Light
Operation
Before Operation
Performing Daily Maintenance
Checking the Interlock Switches
Checking the Traction Pedal Start-Interlock
Checking the Cutting Unit Drive
Switch Start-Interlock
Checking the Parking Brake and
Seat Run-Interlock
Checking the Parking Brake and
Traction Pedal Run-Interlock
Checking the Seat and Traction
Pedal Run-Interlock
During Operation
Cutting Grass with the Machine
Side-Shifting the Cutting Units
Driving the Machine in Transport
Mode
Maintenance
Recommended Maintenance Schedule
Daily Maintenance Checklist
Pre-Maintenance Procedures
Preparing for Maintenance
Lifting the Front of the Machine
Lifting the Back of the Machine
(Using a Hoist)
Lifting the Back of the Machine
(Using a Jack)
Removing the Battery Cover
Lubrication
Greasing the Bearings and Bushings
Checking the Sealed Bearings
Engine Maintenance
Engine Oil Specifications
Checking the Engine-Oil Level
Changing the Engine Oil and Filter
Servicing the Air Cleaner
Fuel System Maintenance
Inspecting the Fuel Lines and
Connections
Servicing the Fuel/Water Separator
Draining the Fuel/Water Separator
Replacing the Fuel/Water Separator
Filter
Bleeding Air from the Injectors
Electrical System Maintenance
Drive System Maintenance
Checking the Tire Pressure
Torquing the Wheel Lug Nuts
Torquing the Axle Hub Nuts
Adjusting the Traction Drive for
Neutral
Cooling System Maintenance
Checking the Coolant Level
Cleaning the Engine Cooling System
Brake Maintenance
Adjusting the Parking Brake
Belt Maintenance
Servicing the Engine Belts
Tensioning the Alternator/Fan
Belt
Replacing the Hydrostat Drive
Belt
Controls Maintenance
Adjusting Mow Ground Speed
Hydraulic System Maintenance
Hydraulic Fluid Specifications
Checking the Hydraulic Fluid
Inspecting the Hydraulic Lines
and Hoses
Changing the Hydraulic Fluid
Changing the Hydraulic Filter
Cutting Unit Maintenance
Checking the Reel-to-Bedknife
Contact
Backlapping the Cutting Units
Lapping the Reels and Bedknife
Troubleshooting
Using the Standard Control Module
(SCM)
Troubleshooting the Standard Control
Module (SCM)
California Proposition 65 Warning
Information